Teka HA-870 Hoja De Características página 14

Programming the Cooking Stop Time
1 Press on the clock sensor (2) several times
until the symbol (15) lights up.
2 Select the cooking stop time by pressing
the or sensors.
3 Two consecutive beeps will then sound and
the display will show the remaining cooking
time. The (15) symbol will flash slowly to
indicate that the oven will switch itself
automatically.
4 Select a cooking function and temperature.
5 Once it is the set time, the oven will turn
off, an alarm will sound and the (15) symbol
will flash more quickly.
6 Press on any sensor on the control panel to
stop the alarm.
You can change the programmed cooking stop
time at any moment by pressing on the clock
sensor (2) until the (15) symbol flashes and
then by pressing on the + or – sensors. The
two beeps you hear after that will confirm the
new time has been set.
You can use this function even if you are
already cooking with the oven. If this is the
case, follow all of the above instructions
except No. 4.
Programming Cooking Time and Cooking
Stop Time
11 Press on the clock sensor (2). The symbol
(14) will light up.
12 Select the cooking time by pressing the
+ + or + +sensors.
13 Two consecutive beeps will then sound,
and the display will show the remaining
cooking time. The (14) symbol will flash
slowly.
14 Press on the clock sensor (2) several
times until the symbol15) lights up.
26
15 Select the cooking stop time by pressing
the or sensors.
16 This will be confirmed by two beeps. The
current time will show on the display and
the (15) symbol will remain lit.
17 Select a cooking function and temperature.
18 The oven will remain off, with the(15)
symbol lit and the (14) symbol flashing
slowly. The clock will show the current time
and the inside light will remain off. The
oven is now programmed.
19 When it is time to start cooking, the oven
will switch on and will operate for the
programmed cooking time. The clock
display will show the remaining cooking
time.
10 Once the set time is reached, the oven will
turn off, an alarm will sound and the(14)
and (15) symbols will flash.
11 Press on any sensor on the control panel
to stop the alarm.
If you wish to change the cooking stop time
while cooking is in progress, press on the
clock sensor until the (15) symbol flashes.
You can then change the cooking stop time by
pressing on the + or – sensors. The two
beeps you hear after that will confirm the new
time has been set.
Child Safety Function
This function locks the oven, preventing small
children from playing with it. To turn on the
function, press on the (16) symbol until you
hear a long beep and see several flashing
dots between the digits of the temperature
display (4). The oven is now locked.
To turn off the child lock, keep the
symbol pressed until a long beep sounds.
Use of the meat probe
The meat probe measures the temperature
inside the roast. When this temperature reach-
es a previously set level, the oven will turn off
automatically. Cooking with the meat probe
ensures optimum results for any type of meat
or size of roast.
Placing the meat probe
• Use only the original meat probe.
• Place the probe before roasting begins.
• Insert the probe into the side of the roast so
that the point reaches its centre.
• Insert the entire probe, up to the handle.
• It is recommended to turn the roast over
half-way through cooking. Bear this in mind
when placing the probe to avoid problems
with it later.
(16) Caution
In the event of power failure, your electronic
clock timer settings will be erased and 12:00
will flash on the clock display. Reset the clock
and programme again.
• The point of the probe must not be touching
the bone or fatty areas. Also, it should not
be in a hollow area, which could happen
with poultry.
Use of the meat probe
• Put the roast with the probe already in it into
the oven.
• Plug the probe into the socket in the upper
left side of the oven.
• When you plug it in, you will see a
recommended temperature (65
probe temperature display (3) on the control
panel.
• If you want to change the recommended
temperature, touch the sensor
then the sensors or .
• You will hear two beeps confirming the new
temperature selected.
o C) on the
(17) and
27