Worx WG154 Manual Del Usuario página 10

To rotate the trimmer head to edging—first hold the
trimmer shaft as shown in Fig. E3---then with your
other hand hold the trimmer head - Push away and
rotate 180 degrees and then release- the trimmer will
then lock into the edging position automatically—
Fig. E4
NOTE: The trimmer head will only rotate in one
direction.
Take extra caution while edging as objects can be
thrown from the trimmer line.
AUTOMATIC LINE FEED SYSTEM
When initially switching ON the trimmer, a small
length of line is fed out.
A 'clattering' noise will be heard when the lines
hit the line cutter. DO NOT BE ALARMED, this is
normal. After about 5 seconds the line will be cut to
the correct length and the noise will reduce as the
motor receives full speed.
If the noise of the line being cut can't be heard, more
line will need to be fed out.
To feed more line, it is first necessary to allow the
trimmer to stop completely, then restart, allowing
the motor to reach full speed.
Repeat above until you hear the lines hitting against
the line cutter.
TO MANUALLY FEED THE LINE (See Fig. F1)
ALWAYS REMOVE THE BATTERY PACK
BEFORE ADJUSTING THE TRIMMER HEAD
10
POSITION
If required, line can be feed out manually.
To operate, press and release manual line feed
button (13), while gently pulling out the line until it is
long enough to reach the line cutter.
If the line extends past the line cutter, too much line
has been fed out.
If too much line is fed out, remove the spool cap and
turn spool counter-clockwise until the line is at the
desired length.
TO REMOVE THE CAP (See Fig. F2)
● Press and hold the two latches (9).
● Pull cap away from the spool holder.
● When refitting the spool cap, keep all areas
of the cap and spool holder clean.
● Replace the cap, pressing firmly down towards
the spool holder to ensure cap is fully located
into position.
● Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
REPLACE THE TRIMMER LINE AND SPOOL
(See Fig. G)
ALWAYS REMOVE THE BATTERY PACK
BEFORE ADJUSTING THE TRIMMER HEAD
POSITION
● Remove Spool Cap Cover.
● For your convenience it is recommended you
2 in 1: Trimmer / Edger
buy replacement spools with the trimmer line
preinstalled.
● Remove the old Spool from Spool Holder. Clear
any broken line or cutting debris from the spool
area.
● Pull the line from the new replacement Spool
through the eyelet of the Spool Holder.
● Place new Spool into the holder with the cut out
areas of the Spool facing inward or down.
When installed into the Spool Holder, the
smooth side of the Spool should be visible.
● Release line from cleat on the Spool.
● Refit the Spool Cap Cover.
TO MANUALLY WIND LINE (See Fig. H1-H3)
Take approximately 10ft (3m) of line. Insert 0.065
inches (1.65mm) of line into the Spool holes and
wind line in the direction of the arrows on the top of
the Spool.
Leave approximately 4 inches (100mm) of line
unwound and place into the cleat.
Ensure that the line is neatly coiled on the Spool.
Failure to do so will impair the efficiency of the
automatic line feed.
Then fit the Spool as described above in "Replace
the trimmer line and Spool"
STORING YOUR GRASS
TRIMMER
Always remove the battery pack from
your trimmer after use.
Store in a dry place where the trimmer and battery
can be protected from damage.
MAINTENANCE
Always remove the battery pack from
your trimmer after use.
Always check the product prior to being used for any
damage.
Never operate your product if it is damaged.
Your power tool requires no additional lubrication
or maintenance. There are no user serviceable parts
in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with
a dry cloth. Always store your power tool in a dry
place. Keep the motor ventilation slots clean. Keep
all working controls free of dust.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0℃-45℃.
The recommended ambient temperature range for
the charging system during charging is 0℃-40℃.
EN