DNP DS-RX1 Guia De Inicio Rapido página 3

Do not set the printer up in dusty or overly humid places. This could cause fire or electric shock, or damage the printer.
・
Do not set the printer up on an unstable surface. It could fall and cause injury to the user or others.
・
Do not allow foreign objects to enter the printer. They could cause electric shock, short circuit, or fire, or break the printer. If something falls into the printer,
・
immediately turn the power OFF, and call a service representative.
Do not open the cover while printing. This could break the printer.
・
Do not spill or spray liquids or chemicals into the printer.
・
When cleaning the cover, do not use thinner, trichloroethane, benzene, ketone-based cleaners, or chemically treated cloths. They could discolor or deteriorate
・
the cover.
At least once a year, unplug the power cord, and clean the prongs and the plug. If dust accumulates, it could cause a fire.
・
When printing continuously for long periods of time in a small room, be sure to ventilate properly.
・
If use is intended on a transportation vehicle (train, truck, ship, etc.), please talk to a representative in advance.
・
When disposing of the printer, peripheral items, packaging, or media, please abide by local waste removal ordinances.
・
For details, contact your local government offices.
When unplugging the cord, grip the plug. Do not pull on the cord. It could damage the cord, and cause electric shock or fire.
・
When moving the printer, be sure to unplug the power cord. Otherwise, the cord may be damaged, which could cause fire or electric shock.
・
When not using the printer for extended periods of time, for the sake of safety, be sure to unplug the power cord. It could cause electric shock or fire.
・
The thermal print head gets very hot. Do not touch after printing. There is a danger of burns.
・
Do not touch the gear mechanisms. There is a danger of injury if fingers get caught in the spinning gears.
・
Cautions for Set-up
Prior to operation, read "For Safe Operation" carefully and observe the rules therein.
・
Use care when moving the printer. Never try carrying the printer alone.Dropping it could cause injury or damage to other property.
・
Do not use or store the printer near fire, excessive moisture, in direct sunlight, near an air conditioner or heater, or any other source of unusually high or low
・
mperature or humidity, or excessive dust.
Do not place the printer where chemical reactions occur, such as in a laboratory.
・
Do not set up the printer where there is salinity or corrosive gas in the air.
・
The printer must sit on a firm, level surface where there is ample ventilation.
・
Do not put anything on the top of the printer.
・
Do not place the printer near a radio or television, and do not use the same wall outlet for the printer and radio or television. Radio or television reception could be
・
adversely affected.
Do not use a power voltage or frequency other than those specified.
・
Do not put anything on the power cord or step on it.
・
Do not drag or carry the printer by the power cord or USB cable.
・
Avoid plugging the power cord into an outlet with many loads.
・
Do not bundle the power cord.
・
Always grip the plug housing, not the cord, to plug/unplug the power cord.
・
Make certain the power is turned off before connecting/disconnecting the USB cable.
・
Avoid lengthening the signal cable or connecting it to any noise-producing device. If it is unavoidable, use a shielded cable or twisted pair for each signal.
・
Use a USB cable with shielding suitable for the USB 2.0 specification.
・
Place the printer near the outlet where the power cord can be unplugged easily to shut off power.
・
Use an AC outlet that accepts a three-pronged plug. Otherwise, there may be danger of electric shock.
・
Use the appropriate specified cord set.
・
Only use items that are certified safe according to the standards of the country where they are to be used
This device is not intended for use in the direct field of view at visual display workplaces.
・
To avoid incommoding r eflections at visual display workplaces this device must not be placed in the direct field of view.
Specifications
Model
Manufacturer
Print type
Dimensions
Weight
Power
Power consumption
Operating environment
CAUTION
JR10-M01
CITIZEN SYSTEMS JAPAN CO.,LTD.
Thermal dye sublimation transfer
322mm W × 351mm D × 281mm H
Approx. 13.8 ㎏（printer only）
AC100V-240V 50/60Hz
100V 2.9A 240V 1.2A
Temp. 5～35℃ in natural conditions
Humidity 35～80% with no condensation