Operation; Maintenance; Ordering Replacement Parts - Luna BCS 250 Traducción De Instrucciones Originales En Inglés

•
The stop rail (25) can be moved in longitudinal direction in
order to prevent the workpiece from becoming jammed.
•
Rule of thumb: The rear end of the stop comes up against an
imaginary line that begins roughly at the center of the blade and
runs at an angle of 45° to the rear.
•
Set the required cutting width
• Slacken the knurled screws (26) and push the stop rail (25)
forward until it touches the imaginary 45° line.
• Retighten the knurled screws (26).
8.4. Cross stop (Figure 9)
•
Slide the cross stop (14) into the groove (38) of the table.
•
Slacken the knurled screw (32).
•
Turn the cross stop (14) until the arrow points to the angle
required.
•
Retighten the knurled screw (32).
•
When cutting large parts of work pieces you can use the stop rail
(25) from the parallel stop (7) to extend the length of the cross
stop (14) (Fig. 15)
Important!
•
Do not push the stop rail (25) too far toward the blade.
•
The distance between the stop rail (25) and the blade (4) should
be approx. 2 cm.
8.5. Setting the angle (Fig. 16)
•
Undo the fixing handle (9).
•
Turn the handle to set the desired angle on the scale.
•
Lock the fixing handle again in the required angle position.

9. OPERATION

Important!!
•
After every new adjustment we recommend you to make a trial
cut in order to check the new settings.
•
After switching on the saw, wait for the blade to reach its
maximum speed of rotation before commencing with the cut.
•
Take extra care when starting the cut!
9.1. Making longitudinal cuts (Figure 23)
Longitudinal cutting (also known as slitting) is when you use the
saw to cut along the grain of the wood. Press one edge of the work-
piece against the parallel stop (7) while the flat side lies on the
saw table (1). The guard hood (2) must always be lowered over the
workpiece. When you make a longitudinal cut, never adopt a work-
ing position that is in line with the cutting direction.
•
Set the parallel stop (7) in accordance with the workpiece height
and the desired width. (See 8.3.)
•
Switch on the saw.
•
Place your hands (with fingers closed) flat on the workpiece and
push the workpiece along the parallel stop (7) and into the blade
(4).
•
Guide at the side with your left or right hand (depending on the
position of the parallel stop) only as far as the front edge of the
guard hood.
•
Always push the workpiece through to the end of the splitter (5).
•
The offcut piece remains on the saw table (1) until the blade (4)
is back in its position of rest.
•
Secure long workpieces against falling off at the end of the cut
(e.g. with a roller stand etc.).
9.1.2. Cutting narrow workpieces (Fig. 24)
•
Be sure to use a push stick (3) when making longitudinal cuts
in workpieces smaller than 120 mm in width. A push block is
supplied with the saw!
Replace a worn or damaged push stick immediately.
9.1.3. Cutting extremely narrow workpieces (Fig.25)
•
Be sure to use a push block when making longitudinal cuts in
very narrow workpieces with a width of 30 mm and less.
•
The low guide face of the parallel stop is best used in this case.
There is no push block supplied with the saw! (Available from your
specialist dealer). Replace the push block without delay when it
becomes worn.
9.1.4. Making concealed cuts (Fig. 26)
Concealed cuts and groove cuts are possible thanks to the remov-
able blade guard and the infinitely adjustable cutting height.
•
Remove the blade guard (2) (see 7.3).
•
Set the splitter (5) for concealed cuts (see 7.4.2.)
•
Set the desired cutting depth (Fig. 8.2)
•
Mount the parallel stop (7) to the right of the blade and set the
desired width (8.3.2)
•
Push the workpiece into the blade (4). Make sure that the
workpiece lies solidly on the saw table (1).
•
Select the cutting sequence so that the cut strips fall away on
the left side of the blade and jamming between the stop and the
blade is prevented (risk of kick-back).
•
After you have finished cutting, refit the blade guard (2)
immediately.
9.1.5. Making bevel cuts (Fig. 16/27)
Bevel cuts must always be used using the parallel stop (7).
•
Set the blade (4) to the desired angle. (See 8.5.)
•
Set the parallel stop (7) in accordance with the workpiece width
and height (see 8.3.1)
•
Carry out the cut in accordance with the workpiece width (see
9.1.1., 9.1.2 and 9.1.3.)
9.1.6. Making cross cuts (Fig. 28)
•
Slide the cross stop (14) into one of the grooves (49) in the table
and adjust to the required angle. (See 8.4.) If you also want to
tilt the blade (4), use the groove (49) which prevents your hand
and the cross stop from making contact with the blade guard.
•
If necessary, use the stop rail (25).
•
Press the workpiece firmly against the cross stop (14).
•
Switch on the saw.
•
Push the cross stop (14) and the workpiece toward the blade in
order to make the cut.
•
Important: Always hold the guided part of the workpiece.
Never hold the part which is to be cut off.
•
Push the cross stop (14) forward until the workpiece is cut all
the way through.
•
Switch off the saw again. Do not remove the offcut until the
blade has stopped rotating.

10. MAINTENANCE

•
Important! Pull out the power plug fi rst.
•
Remove dust and dirt regularly from the machine. Cleaning is
best carried out with a fine brush or a cloth.
•
Never use caustic agents to clean plastic parts.

11. ORDERING REPLACEMENT PARTS

Please provide the following information on all orders for replace-
ment parts:
•
Model/type of device
•
Article number of the device
•
ID number of device
•
Number of the required replacement part
46