Dimplex SP420 Manual Del Usuario página 7

Manual & Remote Operation
Setting Operation
Flame Effect only Press the ' I ' button (Switch 3)
Flame Effect & Heat On Press the ' I ' button again (Switch 3) Bottom Neon
To go to the
' O ' button (Switch S3).
Pressing the ' O ' button on the remote turns off the light & heat settings. To
resume press the ' I ' button until the desired setting is reached - see Fig. 8.
To increase or decrease the brightness of the flames, use the dimmer button
(Switch S4 on the fire or the
any setting between full brightness and the flames totally off. The heat setting will
remain the same.
To turn off the power the Standby Switch (Switch S1) must be turned 'OFF'.
Note : Every time that manual mode is selected the previous light and heat
settings come on automatically.
Replacing the remote control
The new remote control must be set up as follows:
Press switch S1 to ON.
Press switch S2 to AUTO (see Fig. 6).
Press switch S3 to O for more than 3 seconds until the LED's are on (see Fig. 7).
Press the ' I ' button on the remote control.
Now the heater has learned the serial number from the remote control and will
work with this remote control only (this procedure is repeatable many times).
Lamp Replacement - SP420
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation. For this reason,
allow the lamps to cool down after switching off the appliance.
The front panel will need to be removed in order to change lamps –see Fig. 10.
Warning - The front panel is heavy and easily damaged.
The front panel is fixed with 4 spring loaded pins (see 'a' in Fig. 9) and is supported
at the top by the chassis.
To gain access to lamps please apply the following procedure:
While holding the front panel by its sides with both hands, carefully pull forwards
the panel at the bottom until the pins detach from the clips - see Fig. 9.
When the bottom holding pins are undone, carefully pull forwards at the top until
the top pins detach and then lift the
To gain access to the bulbs remove the screws at 'A' to remove the cover bracket
'X' - see Fig. 10a.
For access to the bottom bulbs, carefully slide the flexible rotisserie (see 'a' in
Fig. 11) to one side ensuring that the rubber grommet is not lost (see 'b' in Fig.
11).
Remove the defective lamp by unscrewing it (see Fig. 11).
Replace with a 60W E14 SES Clear Candle bulb, rotating it. Take care not to
over-tighten the lamp.
Steps for reassembling the heater
1. Refit the rotisserie making sure that the rubber grommet is carefully pushed
into the slotted hole on the axial bracket.
2. Replace the cover bracket 'X' - see Fig. 10a.
3. Replace the front by aligning the slots on the front frame and making sure
that it catches fully on the support brackets.
The magnets on the chassis will hold the front flush to the main body.
Lamp Replacement – SP920
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
REMOVING LAMPS.
Warning - The lamps reach high temperatures during operation. For this reason,
allow the lamps to cool down after switching off the appliance.
The front panel will need to be removed in order to change lamps – see Fig. 12.
Warning - The front panel is heavy and easily damaged.
The front panel is supported at the top by the chassis and held tight by magnets
at the top and bottom.
To gain access to lamps please apply the following procedure:
While holding the front panel by its sides with both hands, carefully lift the panel
up (1) and then away (2) from the main body - see Fig. 12.
To gain access to the bulbs remove the screws at 'A' to remove the cover bracket
'X' and the screws at 'B' to remove the cover bracket 'Y' - see Fig. 10a.
The bottom cover bracket 'X' is also held on by magnets. To remove this bracket,
(1) gently tilt the bottom of the bracket out and then (2) lift out - see Fig. 10a.
For access to the bottom bulbs, carefully slide the flexible rotisserie (see 'a' in
Fig. 11) to one side ensuring that the rubber grommet is not lost (see 'b' in Fig.
11).
Remove the defective lamp by unscrewing it (see Fig. 11).
Setting
Top Neon
previous settings press
button on the Remote Control). You can have
front panel up and out (see Fig. 10).
- 2 -
Replace with a 60W E14 SES Clear Candle bulb, rotating it. Take care not to
over-tighten the lamp.
Steps for reassembling the heater
1. Refit the rotisserie making sure that the rubber grommet is carefully pushed
into the slotted hole on the axial bracket.
2. Replace the cover brackets 'X' and 'Y' ensuring that the magnets at the top
the
of cover bracket 'Y' catch the fuel effect bracket 'C' to prevent vibration - see
Fig. 10a.
3. Replace the front by aligning the slots on the front frame and making sure
that it catches fully on the support brackets.
The magnets on the chassis will hold the front flush to the main body.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive cleaners. The
glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use
proprietary glass cleaners.
After Sales Service
Should you require after sales service or should you need to purchase any spares,
please contact the retailer from whom the appliance was purchased or contact
the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance as this may result
in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
UK