Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
FEATURES
UNIT SFL-282HD SFL-282HD SFL-295HD SFL-295HD SFL-315HD SFL-315HD
Voltage
V
110
Frequency
Hz
60
Power Ra ng
CV
2
Heigth
mm
1900
Width
mm
900
Depth
mm
980
Net Weight
kg
110
Gross Weight
kg
164
Maximum Cu ng Height
mm
350
Maximum Cu ng Width
mm
330
3.INSTALLATION AND PRE-OPERATION
3.1 Placing
The equipment must be installed over a firm and level
working surface, in a 1100 mm x 1500 mm area.
3.2 Electrical Installa on
The power plug has 3 pins the middle pin is the ground . All
the 3 pins must be properly connected.
3.2 Pre-Opera on
Before to use the equipment all the parts which could get
into contact with the product to be processed shall be
washed with water and neutral soap ( see item 5 CLEANING).
4. OPERATION
4.1 Star ng
To start the equipment follow the below instruc ons:
- Make sure all the protec ons and the door are in due place
and the door is closed;
- Plug the equipment to the electric network;
- Rotate the Main Switch # 15 (Pic.01) on posi on "ON" to
turn on the equipment.
4.2 Opera on Procedures
4.2.1 Doors
The Doors #02 (Pic. 01) shall be closed as long as the
equipment is in use.
4.2.2 Thickness Guide
To obtain several same thickness slices adjust the Thickness
Guide #06 (Pic.01) as desired. That for turn the thickness
guide handle counter clockwise ge ng the guide free, then
place the Thickness Guide at the desired thickness and ght
the Thickness Guide Handle turning it clockwise.
4.2.3 Blade
The Blade must be installed with the teeth turned
towards the front side of the machine and with the points
downwards.
To regulate (stretch) the Blade #04 (Pic.01) turn clockwise
the Blade Tensio Regulator Handle # 01 (Pic.01) un l it stops.
220
110
220
110
50 or 60
60
50 or 60
60
2
2
2
2
1900
1965
1965
2000
900
900
900
970
980
980
980
1050
110
110
110
127
164
164
164
203
350
410
410
380
330
330
330
380
Figura 02
4.2.4 Blade Guide
With the equipment switched OFF, turn the Handle #12
(Pic. 01) counter clockwise to get free the Blade Guide #11
(Pic.01). Then adjust the Blade Guide to have it no more
than the height of the product to be cut and ght the Handle
#12 (Pic.01).
4.2.5 Lower Wheel
The Lower Wheel #07 (Pic. 01) is assembled on the lower
bearing sha .
4.2.6 Upper Wheel
The Upper Wheel # 03 (Pic. 01) has in its frame the sha and
the bearing.
Before to start the machine
Push the Movable Table #10 (Pic. 01) totally to the front side
of the machine.
Place the product to be cut on the Movable Table.
Choice the slices thickness and adjust the Thickness Guide
#06 (Pic.01).
Adjust the Blade Guide #11 (Pic. 01) to no more than the
height of the product to be cut.
Stay in front of the machine to have a front sight of the
Blade.
Start the Machine
To start the machine turn the ON/OFF Switch #13 (Pic.01)
bu on "I" (ON).
Catch the Movable Table with the le hand and push against
220
60 or 50
2
2000
970
1050
127
203
380
380
Publicidad
Tabla de contenido
