Homelite F-3045 Manual De Utilización página 20

Trimmer/Brushcutter-17 lgs
GB
F D E
SPECIFIC SAFETY RULES FOR
BRUSHCUTTER AND BLADE USE
Do not attempt to touch or stop the blade when it
is rotating.
A coasting blade can cause injury while it continues to
spin after the engine is stopped or throttle trigger
released. Maintain proper control until the blade has
completely stopped rotating.
Replace any damaged blade. Always make sure blade
is installed correctly and securely fastened before
each use. Failure to do so can cause serious injury.
Use only the manufacturer's replacement TRI-ARC
blade intended for use on this brushcutter. Do not use
any other blade.
The TRI-ARC blade is suited for cutting pulpy weeds
and vines only. Do not use for any other purpose.
Never use the TRI-ARC blade to cut woody brush.
Exercise extreme caution when using the blade with this
unit. Blade thrust is the reaction which may occur when
the spinning blade contacts anything it cannot cut.
This contact may cause the blade to stop for an
instant, and suddenly "thrust" the unit away from the
object that was hit. This reaction can be violent enough
to cause the operator to lose control of the unit. Blade
thrust can occur without warning if the blade snags,
stalls or binds. This is more likely to occur in areas
where it is difficult to see the material being cut.
For cutting ease and safety, approach the weeds being
cut from the right to the left. In the event that an
unexpected object or woody stock is encountered, this
could minimise the blade thrust reaction.
Never cut any material over 13 mm (1/2 in) diameter.
Always wear the shoulder strap when using the
brushcutter and adjust to a comfortable operating
position. Maintain a firm grip on both handles while
cutting with a blade. Keep the blade away from body and
below waist. Never use the brushcutter with the blade
located 76 cm (30 in) or more above the ground level.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
SPECIFICATIONS
Weight
Without fuel, cutting attachment
With blade
With string head
Fuel tank volume
Cutting swath
Engine displacement
30/09/03 17:00
I P NL S DK
English
Maximum engine performance
(in accordance with ISO 8893)
Maximum rotational frequency
of the spindle
Engine Speed (rotational frequency)
at recommended max.
spindle rotational frequency
Engine speed (rotational frequency)
at idle
Fuel consumption (in accordance with ISO 8893) at max.
engine performance
Specific fuel consumption (in accordance with ISO 8893)
at max. engine performance
Vibration level idling
Vibration level racing
Sound pressure level
(in accordance with EN ISO 11806:
1997, ISO 7917:1987)
Sound power level (in accordance
with ISO 10884)
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10 BLADE GUARD
11. TRI-ARC BLADE
12. GEAR HEAD
13. SHAFT
14. COUPLER
15. FRONT "J" HANDLE
16. IGNITION SWITCH
17. THROTTLE INTERLOCK 47. SPOOL RETAINER
18. EXTENSION SHAFT
19. GUIDE RECESS
20. POSITIONING HOLE
21. HANGER CAP
5.58 kg
22. HOLE
5.90 kg
23. BUTTON
5.77 kg
24. BOLT 1/4 -20 x 1 in.
425 cm 3 25. BOLT 1/4 -20 x 1 1/2 in.
26. SPACER
457 mm
27. FLAT WASHER
3
30 cm
28. LOCK WASHER
29. HEX NUT
14
Page 14
N FIN GR H CZ
- Front Handle
- Rear Handle
- Front Handle
- Rear Handle .
CUTTING LINE 30. BOTTOM CLAMP
GRASS DEFLECTOR 31. TOP CLAMP
LINE CUT-OFF BLADE 32. QUICK RELEASE TAB
ENGINE HOUSING 33. LATCH
STARTER GRIP 35. REAR HOUSING
THROTTLE TRIGGER 36. SILENCER GUARD
STRAP HANGER 37. SCREWS
SHOULDER STRAP 38. TORQUE WRENCH
KNOB 39. BENT END OF SILENCER
GUARD
40. OPENING IN REAR HOUSING
41. MOUNTING BRACKET
42. NOTCHES
43. LOCKING TABS
44. THREADED MOUNTING
PLATES
45. SPANNER (16 mm)
46. DRIVE CONNECTOR
48. STRING HEAD
49. HOLDING PIN
50. UPPER FLANGE WASHER
51. SPANNER (13 mm)
52. BLADE NUT
53. CUPPED WASHER
56. PRIMER BULB
57. WARM START POSITION
58. COLD START POSITION
59. LEVER
60. SPRING
61. SLOTS
RUS RO PL
0.78 kW
10,000/min -1
12,500/min -1
-1
2,000-2,500/min
0.52 kg/h
0.47 kg/h
4.9
5.8
5.1
6.2
99
113