Publicidad
Idiomas disponibles
Idiomas disponibles
Trimmer/Brushcutter-17 lgs
GB
F
D
E
ASSEMBLY
INSTALLING THE STRING HEAD (Fig. 9)
1. Install the upper flange washer onto the gear shaft with
the hollow side towards the gear head.
2. Place the holding pin through the slot in the upper
flange washer and the hole in the gear head. Using the
16 mm (5/8 in) spanner supplied, turn the drive
connector anticlockwise to install. Tighten securely.
3. Place the string head on the drive connector.
4. Place the holding pin through the slot in the upper
flange washer and the hole in the gear head. Install the
spool retainer and turn anticlockwise to tighten securely.
OPERATION
FUEL AND REFUELLING
HANDLING THE FUEL SAFELY
Always handle fuel with care. It is highly flammable.
Always refuel outdoors where there are no sparks
and flames. Do not inhale fuel vapour.
Do not let petrol or oil come in contact with your skin.
Keep petrol and oil away from the eyes. If petrol or oil
comes in contact with the eyes, wash them
immediately with clean water. If irritation is still
present, see a doctor immediately.
Clean up spilled fuel immediately.
MIXING THE FUEL
This product is powered by a 2-cycle engine and
requires pre-mixing petrol and 2-cycle oil. Pre-mix
unleaded petrol and 2-cycle engine oil in a clean
container approved for petrol.
This engine is certified to operate on unleaded petrol
intended for motor vehicle use with an octane rating
of 87 ([R + M] / 2) or higher.
Do not use any type of pre-mixed petrol/oil from fuel
service stations. This includes the pre-mixed petrol/oil
intended for use in mopeds, motorcycles etc.
Use high a quality 2-cycle self-mixing oil for air-cooled
engines. Do not use motor vehicle oil or 2-cycle
outboard oil.
30/09/03
17:00
I
P
NL
S
DK
English
FILLING THE TANK
1. Clean surface round fuel cap to prevent contamination.
2. Loosen fuel cap slowly to release pressure and to
3. Carefully pour fuel mixture into the tank. Avoid spillage.
4. Prior to replacing the fuel cap, clean and inspect
5. Immediately replace fuel cap and hand tighten.
NOTE: It is normal for smoke to be emitted from a new
engine during and after first use.
1 Litre
2 Litres
3 Litres
4 Litres
5 Litres
OPERATING THE TRIMMER (Fig. 11)
Hold the trimmer/brushcutter with the right hand on the
rear handle and the left hand on the front handle. Keep a
firm grip with both hands while in operation. Trimmer
should be held at a comfortable position with the trigger
handle about hip height.
Always operate trimmer at full throttle. Cut tall grass from
the top down. This will prevent grass from wrapping
round the shaft housing and string head, which may
cause damage from overheating. If grass becomes
wrapped round the string head, stop the engine,
disconnect the sparking plug wire, and remove the grass.
Prolonged cutting at partial throttle will result in oil
dripping from the silencer.
17
Page 17
N
FIN
GR
H
CZ
Mix 2% oil into the petrol. This is a 50:1 ratio.
Mix the fuel thoroughly and also each time before
refuelling.
Mix in small quantities. Do not mix quantities larger
than usable in a 30 day period. A 2-cycle oil
containing a fuel stabiliser is recommended.
keep fuel from escaping around the cap.
the gasket.
Wipe up any fuel spillage. Move 9 m (30 ft) away from
refuelling site before starting engine.
WARNING
Always shut off engine before refuelling.
Never add fuel to a machine with a running or hot
engine. Move at least 9 m (30 ft) from refuelling
site before starting engine. Do not smoke!
+
20 ml
+
40 ml
+
60 ml
+
80 ml
+
100 ml
RUS
RO
PL
}
=
=
=
50:1
=
=
Publicidad
