Using The Machine; Checking The Battery; Safety Checks; General Safety Check - Stiga Cruiser 430 Li 80 Serie Manual De Instrucciones

6.

USING THE MACHINE

The safety regulations to follow are described in
chap. 2. Strictly comply with these indications to avoid
serious risks or dangers.
6.1 PRELIMINARY PROCEDURES
Before starting work , it is necessary to carry out
several checks and operations to ensure you
can work efficiently and in maximum safety:
Make sure the safety key is not inserted in its housing.
Place the machine in a stable horizontal
position on the ground.
6.1.1

Checking the battery

Before using the machine for the first time after
purchase, fully charge the battery following
the instructions in the battery booklet.
Before every use of the machine, check the battery charge
status according to the instructions in the battery booklet.
6.1.2 Preparing the machine before starting work
NOTE This machine can be used to mow lawns in a
number of different ways; before starting work, prepare
the machine based on how the lawn is to be mowed.
a. Preparation for grass cutting and
collection in the grass catcher:
1. Lift the rear discharge guard (Fig.17.A) and fasten
the grass catcher (Fig.17.B) correctly as shown in
the illustration.
2. On models with a side discharge: make sure that
the side discharge guard (Fig.18.B) is lowered.
b. Preparation for mowing and grass
rear discharge onto the ground:
1. Remove the grass catcher and check that the rear
discharge guard (Fig.18.A) maintains its lowered
position.
2. On models with a side discharge: make sure that
the side discharge guard (Fig.18.B) is lowered.
c. Preparation for mowing and mulching:
1. Lift the rear discharge guard (Fig.19.A) and fit
the chute flap (Fig.19.B) in the discharge ope-
ning holding it inclined slightly to the right.
2. Fasten in place by inserting the two pins
(Fig.19.C) into the designated holes until the
toothed coupling clicks into place (Fig.19.D).
On models with a side discharge: make sure that
3.
the side discharge guard (Fig.18.B) is lowered.
To remove the chute flap:
1. Lift the rear discharge guard (Fig.19.A).
2. Press the centre to release the to-
othed coupling (Fig.19.D).
d. Preparation for mowing and grass
side discharge onto the ground:
1. Lift the rear discharge guard (Fig.19.A) and fit
the chute flap (Fig.20.B) in the discharge ope-
ning holding it inclined slightly to the right.
2. Fasten in place by inserting the two pins
(Fig.20.C) into the designated holes until the
toothed coupling clicks into place (Fig.20.D).
3. Lift the side discharge guard (Fig.20.A).
4. Insert the side discharge chute (Fig.20.E).
5. Close the side discharge guard (Fig.20.A) so that the
side discharge chute (Fig.20.E) is locked in place.
To remove the chute flap:
1. Lift the rear discharge guard (Fig.19.A).
2. Press the centre to release the to-
othed coupling (Fig.19.D).
6.1.3 Cutting height adjustment
Adjust the cutting height as indicated in (par. 5.4).
6.2

SAFETY CHECKS

Run the following safety checks and check that the
results correspond to those outlined on the tables.
Always carry out the safety checks before use.
6.2.1

General safety check

Object
Grips
Handle
Cutting means
Rear discharge guard;
grass catcher
Side discharge guard,
side discharge chute
Control lever
Operator presence lever
Drive lever
Battery
Screws/nuts on the
machine and on the
cutting means
EN - 7
Result
Clean, dry.
Fixed firmly to the machine.
Clean, not damaged
or worn.
Good condition. No
damage. Properly installed.
Good condition. No
damage. Properly installed.
The lever must move
freely, it must not need
forcing and should
return automatically
and rapidly back to
the neutral position.
No damage to the casing,
no liquid leakage.
Correctly tightened
(not loose).