Noise And Vibration Information - MIRKA DEROS 325 Serie Instrucciones De Manejo

DEROS 325X CV
Weight 0.8 kg (1.8 lbs)
Degree of protection I

Noise and vibration information

Measured values are determined according to EN 62841.
DEROS
Sound pressure level (L
pA
Sound power level (L )
WA
Sound measurement uncertainty K
Vibration emission value a
Vibration emission uncertainty K
Specifications subject to change without prior notice. Model range may vary between markets.
*
The values stated in the table are derived from laboratory testing in conformity with stated codes and standards and
are not sufficient for risk evaluation. Values measured in a particular work place may be higher than the declared
values. The actual exposure values and amount of risk or harm experienced by an individual are unique to each
situation and depend upon the surrounding environment, the way the individual operates the machinery, the par-
ticular material being worked, work station design and the user's exposure time and physical condition. Mirka Ltd
accepts no responsibility for the consequences of using declared values instead of actual exposure values for any
individual risk assessment.
Further occupational health and safety information can be obtained from the following websites:
https://osha.europa.eu/en (Europe) or http://www.osha.gov (USA)
Proper use of tool
This sander is designed for sanding all types of materials, i.e. metals, wood, stone, plastics, etc. using abrasives designed
for this purpose. Do not use this sander for any other purpose than that specified without consulting the manufacturer
or the manufacturer s authorized supplier. Do not use backing pads that have a working speed of less than 10,000 rpm
free speed. Only use original Mirka backing pads that are designed for optimal performance with the brake seal. Never
mount a backing pad without a spacer washer. Other backing pads may reduce performance and will increase vibration.
The cooling air vents on the housing must be kept clean and free of blockages to ensure air circulation. Any maintenance
or repair work requiring the motor housing to be opened may only be carried out by an authorized service centre.
Work stations
The tool is intended to be operated as a hand-held tool. It is always recommended that the tool should be used when
standing on a solid floor. It can be in any position but before any such use, the operator must be in a secure position,
having a firm grip and footing and be aware that the tool can develop a torque reaction. See the section "Operating
instructions".
How to get started
When unpacking the tool, make sure it is intact, complete and has not been damaged in transport. Never use a damaged
tool.
Before use, check that the backing pad is correctly attached and tightened. Connect the power cord to the tool. Connect
the power cord to a grounded outlet (110  VAC, 50/60Hz).
In order to get the maximum power from this tool it is recommended to use it with the Mirka dust extractor (or other
suitable dust extraction unit) and Mirka net sanding products. The combination of Mirka sanders, Mirka net sanding
products and Mirka dust extractor are the basis of Mirka dust-free sanding solutions.
The power cord from the tool is connected to the mains supply of the dust extractor. By connecting the tool's power cord
to the outlet on the dust extractor it is possible to use the dust extractor s autostart function.
350X CV 550X CV
0.8 kg (1.8 lbs) 1 kg (2.2 lbs)
I I
325X CV 350X CV
) 67 dB(A) 67 dB(A)
78 dB(A) 78 dB(A)
3.0 dB(A) 3.0 dB(A)
* 2
3.1 m/s 3.3 m/s
h
* 2
2.0 m/s 1.5 m/s
625X CV 650X CV
1 kg (2.2 lbs) 1.1 kg (2.4 lbs)
I I
550X CV 625X CV
71 dB(A) 71 dB(A)
82 dB(A) 82 dB(A)
3.0 dB(A) 3.0 dB(A)
2 2 2
3.2 m/s 2.4 m/s
2 2 2
1.5 m/s 1.5 m/s
Mirka® DEROS & 325X, 350X, 550X, 625X, 650X, 680X & 5650X
680X CV 5650X CV
1.1 kg (2.4 lbs) 1.1 kg (2.4 lbs)
I I
650X CV 680X CV 5650X CV
71 dB(A) 71 dB(A) 71 dB(A)
82 dB(A) 82 dB(A) 82 dB(A)
3.0 dB(A) 3.0 dB(A) 3.0 dB(A)
2 2
3.4 m/s 3.5 m/s 3.4 m/s
2 2
1.5 m/s 1.5 m/s 1.5 m/s
en (original)
2
2
13