Galletti MYCOMFORT LARGE Manual Del Usuario página 39

MYCOMFORT LARGE
P09,P11 = 3
The contact status indicates that the unit is in cooling mode.
P09,P11 = 4
The contact status indicates that the unit is in heating mode.
P09,P11 = 5
The contact status indicates if the control in ON or OFF
P09,P11 = 6
The contact status indicates if an alarm is triggered (serious or non-serious, see
"Alarms")
P09,P11 = 7
The contact is used to switch ON/OFF any external device for dehumidifying the air
(cooling mode only). The ON/OFF logic is based on a reading of the humidity in the
room and the SETPOINT selected with parameter P13. It follows the diagram shown:
P09,P11 = 8
The contact is used to switch ON/OFF any external device for humidifying the air
(heating mode only). The ON/OFF logic is based on a reading of the humidity in the
room and the SETPOINT selected with parameter P13. It follows the diagram shown:
P09,P11 = 9
The status of the contact indicates whether the air temperature is too high compared
to the temperature SETPOINT (only in the "summer" mode); the ON/OFF logic is thus
tied to the value of the temperature SETPOINT, according to the following step:
P09,P11 = 10
The status of the contact indicates whether the air temperature is too low compared
to the temperature SETPOINT (only in the "winter" mode); the ON/OFF logic is thus
tied to the value of the temperature SETPOINT, according to the following step:
P09,P11 = 11
The digital output is not governed by the controller; the contact is always open.
P09,P11 = 12
The contact status indicates that water temperature is low. The activation/deactivation
logic follows the step:
È severamente vietata la riproduzione anche parziale di questo manuale / All copying, even partial, of this manual is strictly forbidden
The two tables below provide a detailed explanation of the meaning of the contact
associated with each digital output:
Air humidity
Air humidity
Air temperature
Air temperature
Water temperatu-
re
39
DIGITAL 1 OUTPUT
P10 = 0 (NO
contact)
OPEN CLOSED
contact contact
P09
-- --
0 Not used
SUMME WINTER WINTER
1 Operating mode R
Unit in cooling or
NO YES
2 heating mode
Unit in cooling
NO YES
3 mode
Unit in heating
NO YES
4 mode
OFF ON
5 Controller status
NO YES
6 Alarm triggered
External
dehumidification NO YES
7 call
External
NO YES
8 humidification call
High room
NO YES
9 temperature
Low room
NO YES
10 temperature
-- --
11 Not used
Low water
YES NO
12 temperature
DIGITAL 2 OUTPUT
P12 = 0 (NO
contact)
OPEN CLOSED
contact contact
P11
-- --
0
WINTER WINTER SUMME
SUMME
1 Operating mode R
Unit in cooling or NO YES
2 heating mode
Unit in cooling NO YES
3 mode
Unit in heating NO YES
4 mode
OFF ON
5 Controller status
NO YES
6 Alarm triggered
External NO YES
dehumidification
7 call
External NO YES
8 humidification call
High room NO YES
9 temperature
Low room NO YES
10 temperature
Water circuit YES NO
11 enabled for cooling
Water circuit YES NO
12 enabled for heating
P10 = 1 (NC
contact)
OPEN CLOSED
contact contact
GB
-- --
SUMME
R
YES NO
YES NO
YES NO
ON OFF
YES NO
YES NO
YES NO
YES NO
YES NO
-- --
NO YES
P12 = 1 (NC
contact)
OPEN CLOSED
contact contact
-- --
R
YES NO
YES NO
YES NO
ON OFF
YES NO
YES NO
YES NO
YES NO
YES NO
NO YES
NO YES
FC66002638 - rev. 05