TECHNICAL DATA
Rated input .............................................................................. 900 W ......................... 900 W ............. 900 W ........................900 W
Rated speed ........................................................................ 11000 min
Grinding disk diameter............................................................. 100 mm ...................... 115 mm .......... 115 mm .....................125 mm
Thread of work spindle ............................................................... M 10 .......................... M 14 ...............M 14 ......................... M 14
Weight according EPTA-Procedure 01/2003 .............................. 2,0 kg ......................... 2,0 kg ............. 2,0 kg .........................2,0 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3 dB(A)) ........................................... 90,5 dB (A).................. 90,5 dB (A) ..... 89,0 dB (A) .................90,5 dB (A)
Sound power level(K=3 dB(A)) ............................................. 101,5 dB (A)................ 101,5 dB (A) ... 100,0 dB (A) ...............101,5 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Surface grinding: vibration emission value a
Uncertainty K ............................................................................ 1,5 m/s
Disk sanding: vibration emission level a
Uncertainty K ............................................................................ 1,5 m/s
Rated input ............................................................................ 1100 W .....................................1100 W ..................................1200 W
Rated speed ........................................................................ 11000 min
Grinding disk diameter............................................................. 115 mm ....................................125 mm .................................125 mm
Thread of work spindle ............................................................... M 14 ......................................... M 14 ..................................... M 14
Weight according EPTA-Procedure 01/2003 .............................. 2,3 kg ........................................2,3 kg .....................................2,4 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K=3 dB(A)) ........................................... 90,5 dB (A) ................................90,5 dB (A) .............................90,0 dB (A)
Sound power level(K=3 dB(A)) ............................................. 101,5 dB (A) ..............................101,5 dB (A) ...........................101,0 dB (A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 60745.
Surface grinding: vibration emission value a
Uncertainty K ............................................................................ 1,5 m/s
Disk sanding: vibration emission level a
Uncertainty K ............................................................................ 1,5 m/s
For other applications, e.g. Abrasive Cutting-Of Operations or Wire Brushing other vibration values could occur.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diferent applications, with
diferent accessories or poorly maintained, the vibration emission may difer. This may signiicantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched of or when it is running
but not actually doing the job. This may signiicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the efects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WS 9-100
........................... 5,8 m/s
h
................................... 1,9 m/s
h
WS 11-115
........................... 5,8 m/s
h
................................... 1,9 m/s
h
WS 9-115
220 - 240 V
110 V
-1
............... 11000 min
-1
... 11000 min
...................... 5,8 m/s
.......... 5,6 m/s
2
2
2
...................... 1,5 m/s
2
.......... 1,5 m/s
...................... 1,9 m/s
.......... 2,9 m/s
2
2
2
...................... 1,5 m/s
2
.......... 1,5 m/s
WS 11-125
..............................11000 min
-1
2
....................................5,8 m/s
....................................1,5 m/s
2
2
....................................1,9 m/s
....................................1,5 m/s
2
Angle Grinder
WS 9-125
-1
..............11000 min
-1
.....................5,8 m/s
2
2
2
.....................1,5 m/s
2
.....................1,9 m/s
2
2
2
.....................1,5 m/s
2
WS 12-125 XE
...............2800 - 11000 min
-1
-1
2
.................................6,4 m/s
2
.................................1,5 m/s
2
2
2
.................................1,9 m/s
2
.................................1,5 m/s
2
2
English
GB
13