Technical Specification; Noise Emission - Rapid ESN114 Instrucciones

are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
TACKER SAFETY WARNINGS
Always assume that the tool contains fasteners.
Careless handling of the tacker can result in unexpected
firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the faste-
ner causing an injury.
Do not actuate the tool unless the tool is placed
firmly against the work piece. If the tool is not in con-
tact with the work piece, the fastener may be deflected
away from your target.
Disconnect the tool from the power source when
the fastener jams in the tool. While removing a jam-
med fastener, the tracker may be accidentally activated if
it is plugged in.
Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while attempting to
free a jammed condition.
Do not use this tacker for fastening electrical
cables. It is not designed for electric cable installation
and may damage the insulation of electric cables thereby
causing electric shock or fire hazards.

TECHNICAL SPECIFICATION

Model Number Rapid ESN530, ESN114
Voltage 220~240 V., 50Hz
Current 2 Amp, fuse minimum 10 Amp
Fasteners Rapid 53 Staple,6-14 mm
ESN530 Rapid T8/300 Brad, 15mm
Fasteners Rapid 140 Staple,6-14 mm
ESN114 Rapid T8/300 Brad, 15mm
Magazine Capacity 118mm, number depend on fastener
Speed Maximum average, 20 shots/min
Tool Weight 0.94 kg
6

NOISE EMISSION

A-weighted sound pressure level LpA=91.7 dB(A),
uncertainty K=3 dB(A)
A-weighted sound power level LwA=102,7 dB(A),
uncertainty K=3 dB(A)
Wear hearing protection.
VIBRATION
Vibration total value=6,7 m/s
m/s
2
The declared vibration total value has been
measured in accordance with a standard test
method and may be used for comparing one tool
with another
The declared vibration total value may also be
used in a preliminary assessment of exposure
The vibration emission during actual use of the
power tool can differ from the declared total value
depending on the ways in which the tool is used.
Identify additional safety measures to protect ope-
rator from vibration exposure based on estimation
of exposure in actual use as example: duty cycle
of tool usage and organization of work flow.
ASSEMBLY
DEFINITIONS FIGURE 1 AND 2
Power Cord
On/Off power switch
Trigger Switch
Trigger Safety Lock
Feeder unit
Magazine Latch
Staple output
Work piece
Specification label
LOAD STAPLES/BRADS INTO THE MAGAZINE
1. Turn off the power switch and unplug the tacker
2. Hold tool upside down, squeeze latch and slide maga-
zine open. Fig 3-4
3. Put staples or brads in magazine, legs facing upward
and close magazine. Ensure brad strip stays upright in
magazine. Fig 5 or 6
Use only recommended staples or brads
4. Close magazine and make sure it is securely locked.
Fig 7
REMOVE STAPLES/BRADS FROM THE MAGA-
ZINE
1. Turn off the power switch and unplug the tacker
2. Hold tool upside down, squeeze latch and pull out
magazine.
3. Remove the staples / brads from the magazine
4. Close magazine.
, uncertainty K=1.5
2