Craftsman 315.115800 Manual Del Operador página 9

BATTERY PROTECTION FEATURES
Craftsman 19.2 V lithium-ion battery packs are designed
with features that protect the lithium-ion cells and
maximize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
TO INSTALL BATTERY PACK
See Figure 3, page ii.

Lock switch trigger on the drill by placing the direction
of rotation selector in the center position.

Place battery pack in the drill. Align raised rib on
battery pack with groove inside drill.
CAUTION:
When placing battery pack in the drill,
be sure raised rib on battery pack aligns with groove
inside drill and latches snap into place properly.
Improper assembly of battery pack can cause dam-
age to internal components.
 Make sure the latches on each side of the battery pack
snap in place and battery pack is secured in drill before
beginning operation.
TO REMOVE BATTERY PACK
See Figure 3, page ii.

Lock switch trigger on the drill by placing the direction
of rotation selector in the center position.

Locate the latches on the side of the battery pack and
depress to release the battery pack from the drill.

Remove battery pack from the drill.
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
SWITCH TRIGGER
See Figure 4, page ii.
To turn the drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
OPERATION
FORWARD/REVERSE/CENTER LOCK
See Figure 5, page ii.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
drill held in normal operating position, the direction of
rotation selector should be positioned to the left of the
switch trigger for drilling. The drilling direction is reversed
when the selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when not
in use.
CAUTION:
the chuck to come to a complete stop before chang-
ing the direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool
the drill by running it without a load and at full speed.
KEYLESS CHUCK
See Figure 6, page ii.
The drill has a keyless chuck to tighten or release drill bits
in the chuck jaws. Grasp and hold the collar of the chuck
with one hand. Rotate the chuck body with your other
hand. The arrows on the chuck indicate which direction
to rotate the chuck body in order to LOCK (tighten) or
UNLOCK (release) the drill bit.
WARNING:
hand and use power of the drill to tighten the chuck
jaws on the drill bit. The chuck body could slip in
your hand, or your hand could slip and come in
contact with the rotating drill bit. This could cause an
accident resulting in serious personal injury.
TWO-SPEED GEAR TRAIN
See Figure 7, page ii.
The drill has a two-speed gear train designed for drilling or
driving at LO (1) or HI (2) speeds. A slide switch is located
on top of the drill to select either LO (1) or HI (2) speed.
When using drill in the LO (1) speed range, speed will
decrease and unit will have more power and torque. When
using drill in the HI (2) speed range, speed will increase
and unit will have less power and torque. Use LO (1)
speed for high power and torque applications and HI (2)
speed for fast drilling or driving applications.
9 – English
To prevent gear damage, always allow
Do not hold chuck body with one