precision, durability and smooth running.
Superior-quality, three-jawed collet chucks are
used for tool holding. This enables the reliable
and absolutely centric clamping of even smaller
shafts, fulfi lling the optimum prerequisites for
fi rst-class concentricity and clean working results!
An ergonomically positioned non-slip soft compo-
nent on the forward part of the Micromot 230/E
enables the user to exploit all these advantages
and facilitates precision guiding without fatigue.
Even two-fi ngered guiding of the device presents
no problem.
Provisions have also been made for use with
our drill stand or similar accessories, with the
Micromot 230/E incorporating the familiar 20
mm system fi t in this respect.
3 Scope of delivery
28430
1 pc.
MICROMOT 230/E drill/grinder
1 pc.
Storage case
1 pc.
Operating instructions
1 pc.
Safety guidelines
6 pcs. Collets (1.0-1.5-2.0-2.4-3.0 and 3.2 mm)
1 pc.
Round grinding pin Ø 5mm
1 pc.
Cylinder grinding pin Ø 6mm
1 pc.
Cylinder grinding pin Ø 2.5 mm
1 pc.
Cup grinding pin Ø 7mm
1 pc.
Tungsten carbide micro drill Ø 0.5 mm
1 pc.
Tungsten carbide micro drill Ø 1 mm
1 pc.
Diamond-coated grinding pin Ø 1.8 mm
1 pc.
Finishing miller, ball shaped Ø 2.3 mm
2 pcs. Sanding disc Ø 22 mm (pink colour) of
high-grade corundum, for steel, cast
iron, HSS steels
2 pcs. Sanding disc Ø 22 mm (grey), of sili-
con carbide, fi ne, even grain size with
consistent hardness. For engraving
and frosting of glass, ceramic and stel-
lites, also for grinding of metal, white
cast iron and high-alloy steels
1 pc.
Polishing disc for acrylic glass and Ple-
xiglas
1 pc.
Brass brush for machining brass, brass
alloys, copper, precious metals, semi-
precious stones, plastic and wood. For
cleaning electronic components and
printed circuit boards.
10 pcs. Corundum cutting discs for cutting al-
loyed and non-alloyed steel, stain-less
steels and non-ferrous metals. Can
also be used to cut wood and plastic.
1 pc.
Clamping arbour shaft diameter Ø 3.2 mm
28440
1 pc.
Micromot 230/E
1 pc.
Operating instructions and safety
guide lines
1 pc.
Steel collets (1 - 1.5 – 2 - 2.4 - 3 and
3.2 mm)
4 Technical data
Device:
Length:
Weight (without cable):
Shaft neck:
Motor:
Rotational speed:
Voltage:
Capacity:
Short-term operation:
Noise development:
Vibration:
Please note that the sound and vibration mea-
surements in particular have been performed
with Proxxon bits and cutters. When using
third-party brands we cannot guarantee com-
pliance with the statements given here!
5 Commissioning
Your Micromot 230/E is ready to use on delivery.
Apart from clamping the operational tools, no
special commissioning measures are necessary.
However, please check the device and the opera-
tional tools for any visible wear prior to every use!
approx. 230 mm
approx. 270 g
ø 20 mm.
6000 to 22000/min
230 V
approx. 80 W
KB 5 min
≤ 70 dB (A)
2
< 2,5 m/s
- 17 -