Tecnoinox GD4FG7 Manual Del Usuario página 13

Part 3
Before operating the appliance and initiating cooking,
always fill the recovery tank(s) with clean water "V" (fig.2).
Do not use the appliance with an empty tank; the tank
must always hold a minimum of 2 litres of water.
Press and turn knob "A" (fig.4) from position " " to " " keeping the
knob pressed. At the same time, press ignition button "B" (fig.4)
repeatedly until the pilot light lights up. After the flame has lit, hold
the knob down for approximately 10 seconds (count to 20); so the
thermocouple heats up, keeping the safety valve open.
If the piezoelectric device cannot be used, you can
manually light the flame using a match or a gas lighter.
Close the gas shut-off cock installed above.
Malfunctions are not always caused by the quality of the
components used. These appliances are manufactured using top
quality components. Failures may be caused by dust and dirt
infiltrating the operating components.
Unauthorised persons should never attempt to repair the appliance, or carry out maintenance. Tampering with the appliance voids the
warranty!
Before the appliance is delivered to the user, the following checks
must be carried out:
THERMAL CAPACITY
Check that the gas type and group of the appliance installation area
is the same as that indicated on the plate. If it is not, the appliance
must either be converted or adapted. In this case please refer to the
paragraph "Conversion or Adaptation".
Check that the right nozzles have been installed. Refer to the nozzle
table and check that the nozzles indicated in the table are the same
as those installed on the appliance. An additional thermal capacity
check entails verifying the gas consumed using the volumetric
method: start the burner and after approximately 10 minutes (in
working conditions) check that the gas flow (m
corresponds to that in the nozzle table.
APPEARANCE OF THE FLAME AND PRIMARY AIRFLOW
Use the inspection hole "I" (fig.2) to check the flame.
Faulty parts should only be replaced by qualified personnel.
Disconnect the appliance from the gas distribution network before
carrying out any work.
Only order spare parts from the manufacturer or an
authorised dealer.
Fat recovery drawer
Turning on the burner and the appliance
What to do if the appliance is not going to be used for a long time
What to do in the instance of a malfunction
Operational checks
3 /h or in kg/h)
Replacing parts
After cooking or at the end of the day and only after the
appliance has cooled down, empty the tanks "V" (fig.2).
Off Flame on pilot light
TURNING THE BURNER OFF
Turn the knob to the " " position.
TURNING THE APPLIANCE OFF
Turn the knob to the "
Clean the appliance with soapy water, rinse it, dry it thoroughly and
apply a light layer of liquid paraffin.
In any case, if you suspect the presence of anomalies, close the shut-
off cock and inform the authorised after-sales service.
The flame should be blue and there should be no yellow dots in it; it
must be stable at its base. If the colour of the flame tends towards
yellow it means the primary airflow is not adjusted properly. If there
is excess primary airflow, the flame will be short and tends to burn
above the burner. The primary air capacity is fixed, therefore no
regulation is required. The appearance of the flame must also be
checked 15 minutes after the appliance has been running at full
power. The flame must remain stable even when passing quickly
from minimum to maximum.
USER INSTRUCTIONS
The user must be trained on the correct use and functions of the
appliance. We would like to point out that any alterations made to
the installation area could influence the amount of air required for
combustion and for this reason, operation of the appliance must be
checked once again. When these checks have been completed, test
the appliance for leaks.
After having removed the control panel, all the functional parts of
the appliance are easily accessible.
GB / IE - 3
Burner MAX
" position.
Use
Burner min