Publicidad
Idiomas disponibles
Idiomas disponibles
TM
NOTE: The flat of the leadscrews nut
locate•
on the ball bearing In
the
cros~ad.
Th•
keyway also neado alignment Reoat
stroke adJustmanl ms above.
NOTE; ltlo recommended lhatlhe leadscrew Is greasedweeklywllh
Molykota
BR2
Plus grease (387443) which Is supplied.
SERVICING REQUIREMENTS
General
Notes
Use the followlng luMcants:
Grease -
Molykote BR2 Plus for leadsc:rew.
Grease -
BP FGOO EP for
bea~ngmotor
beerlngo, Inside or outor
case on plslon seat
Grease·
Motykote G68 for bevel geere. gearing and gearbox
bearings.
Grease - . Molykota PG75 Plastlsllp, for 'O' rt.gs.
Grease -
Molykote Longterm W2
ror
splines and guide rod.
MAINTENANCE
It
is recommended that the tool la serviced at 100Dhra running
ame.
DlsmanUe lhe fool using the mq>loded view. Clean
au
components
and lnspectfor wear or damage, exchange I noceu:ary. Apply new
grease to relevant parts In accordance
with
llsl Replace the
front
soal after dlsmanlling tool. Assemble the toot using exploded
view.
Torquovatues gfven are ±5%.
Special tools shown In exploded
.tew
are
In addition
to
normal
work.shop tools.
NOTE: (1)
Protective gloves and eye protecUon should be wom
during cleanlng of parta.
Eating or smoking is
prohibitodwhen cleaning, dismantling or assembllng
tool.
(2)
Worn components should be carotully handlod end
disposed or sarely.
J'lrinted In England
@)
Clean Ing
Requirements:
(1)
Container to
Immerse components.
(2)
Good quallly clean paraffin.
Soak tho components In tho
container containing the paraffin.
Ensure tull
lmmerslon. Romovc tho components from tho container.
thoroughly
dry. Place components in an air tight container untn
required for •ssembly. Dispose of the dirty paraffin In accordance
with
health and safety regulation.
Electrlc
Motor
Electric
motorte~ting
and c:heckiog as necessary should bo carried
out
by
a c:ompetcnt electrician wfth the telovant secUon of lhe Hcaftf\
and Safety Act.
AdJus~ng
tne Timlng Belt (see Ilg. G)
Adjust bolt
to
remove play. Note: high tensioning force Is not
required, over tensioning can cau:!le premature 1allure
end
excessive nol!e.
.---
4 k g - 1
a
:ii
__.\
l
1..,._2'.Smm
FIGURE 6 DRIVE BELT SETTING
8
of 55
Always quote tool number. serlal number and spare part number
when ordertng spares.
O
Copyright 1998, Desouttor, HP2 7DR,
UK.
AU rights reserved. Any unauttlorlzed use or copying olthe contents
or part lhereolls prohibited. This applie•
in
partleular to trademarks,
model denominations.
part
numbcr.s
and drawings.
Use only authorized parts. Any damage or malfunction caused by
the use or unauthorltod parts Is not covered by Warro.nty or Product
LlabRity.
Part No. 441573
Issue
3
03
Ofl
;Ji
~i
'
;'
•,
l
I
Publicidad
