Publicidad
Idiomas disponibles
Idiomas disponibles
HAND-GRIP (PULSE)
On this model the pulse rate is measured by placing
both hands on the sensors (R), located on the
handlebar, as shown in Fig.3. When both hands are
placed on the sensors the heart symbol on the right-
hand side of the screen, marked PULSE, will begin to
flash and after a few seconds a heart rate reading will
be displayed. If both hands are not placed correctly as
shown in Fig.4 then the pulse function will not work.
If a "0" appears on the screen or the heart symbol does
not fl ash then make sure that both hands are placed
on the sensors and that the connectors (130-C) are
connected at the back of the electronic unit.
TELEMETRIC PULSE RATE
(Optional).
The monitor is equipped to receive signals from a
telemetric pulse measurement system.
The system comprises of a receiver and a transmitter
(T) (chest band) Fig.6.
This telemetric pulse rate system takes precedence
over the Hand-grip pulse rate system when both
are used together.
(See telemetric pulse rate instruction book).
TEST MEASUREMENTS.- FITNESS.
This electronic device is equipped with a recovery test
function. This offers you the advantage of being able to
measure how long it takes your heart rate to recover
after having fi nished the exercise.
After fi nishing the exercise leave your hands on the
pulse sensors (R) and press the "PULSE/RECOVERY"
button and this will start a one minute countdown. Only
the Time and Pulse rate function read-outs will remain
displayed. The electronic device will measure your
pulse rate during this minute.
The heart rate recovery time will be displayed on the
Heart rate line. If, at any time during this minute, you
decide
to
abandon
"PULSE/RECOVERY" button and this will take you
back to the main screen. When the minute is up, the
electronic device will work out the difference and your fi
tness rating will be displayed up on the screen: "F1,
F2,..., F5, F16; where F1 is the best (fi tness
"Excellent") and F6 the worst (fi tness "Very Poor").
Pressing the "PULSE/RECOVERY" button will take you
back to the main screen, where the functions will be in
INSTRUCTIONS/USE
this
test
then
press
the same mode as when the TEST began.
The comparison between the worked heart rate and
the recovery heart rate provides a fast, simple method
of gauging how fit you are. Your fitness rating is a
guideline that shows you how fast your heart recovers
after physical exertion. If you exercise regularly then
you will see your fitness rating improve.
The test will not work if the sensor is not connected
correctly or if the error code "E1" appears on the
screen.
The TEST will not work if you do not have both hands
placed on the hand-grip sensors (R) Fig.4 after you
have stopped doing the exercise.
If the error code "E1" is shown on the screen then this
means that you do not have your hands positioned
correctly on the hand-grip sensors (R).
If the error code "E2" appears on the screen, this
means that you have not stopped exercising.
FITTING THE ELECTRONIC MONITOR
Next, connect terminals (128) (130), sticking out of the
handlebar (2), and terminal (B) (C), sticking out of the
monitor (123), Fig.5.
Place the monitor (123) on top of the plate on the main
post (2), as shown in Fig.5, making sure not to pinch
the wires.
Use screws (46) to hold the monitor in place, Fig.5.
TROUBLESHOOTING GUIDE
display comes on but only the Time function Works.
Solution:
a.-Make sure that the connection cable is connected.
(6V Transformer)
Problem: The monitor does not switch on.
Solution:
a.-Check the AC220 V mains connection
b.-Check the output connection from the transformer to
the monitor DC 6v.
c.-Check the monitor cable connections.
d.-Check the cable connections for the main post..
the
Avoid leaving the electronic monitor in direct sunlight
as this might damage the liquid crystal display.
Similarly, do not expose it to water or knocks.
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE
10
MOD. G860
Problem: The
Publicidad
