Battery Installation - Arregui SUPRA Manual De Instrucciones

<EN>
IMPORTANT:
The first opening of the safe
you must use the emergency
key:
• Access the emergency lock.
• Introduce the emergency
key and turn it clockwise.
NOTE: Do not store the emergency key inside the safe

1. BATTERY INSTALLATION

Open the plastic cover located inside the door and place
4 1.5 V AA batteries.
2. PROGRAMMING THE OPENING
CODES
This safe allows to program two secret opening codes-
-one standard and one master, from 3 to 6 digits each.
The initial standard code is 000000 and the initial
master code is 888888. For your security, it´s important
that you change them and configure the codes you
desire.
During the process, use the
digit entered.
Programming the standard code (the safe must be
open):
A. Press 00 and the
SELECT.
B. Press the 0 button. The screen will display SET.
C. Enter your code (3 to 6 digits) and press the
button. The screen will display DONE.
With the door open, verify that the new code operates
correctly (see section 3, opening the safe).
Programming the master code (the safe may be
open or closed):
A. Press 00 and the
SELECT.
B. Press the 1 button. The screen will display OLD.
C. Enter the current master code (888888 the first
time) and press the
display SET (if the code entered is incorrect, it will
display ERROR).
D. Enter the new master code (3 to 6 digits) and press
the button. The screen will display REPEAT.
E. Enter the new master code again and press the
button. The screen will display DONE (if the code
entered is not the same both times, the screen will
display ERROR).
3. OPENING THE SAFE
Enter either of the two active opening codes and press
the button. The screen will display OPEN while the
locks move, and OPENED when the door has opened, and
inside LED lamp will bright 25 seconds automatically.
If an incorrect code is entered, the screen will display
ERROR1, for a second incorrect attempt it will display
- +
EMERGENCY
LOCK
button to delete the last
button. The screen will display
button. The screen will display
button. The screen will
ERROR2, and for a third incorrect attempt it will display
ERROR3 and the system will remain blocked for 5
minutes, indicating by blinking HOLD 5... HOLD 4... etc.
During this time, the keypad cannot be used.
4. CLOSING THE SAFE
With the safe open, press the
display CLOSE while the locks move, and CLOSED when
the door has closed.
NOTE: If the locks encounter an obstacle, they will move
back and leave the door open.
5. OPENING WITH THE EMERGENCY
KEY
If you do not have the opening codes, or if the batteries
have run out and an external battery is not available,
you can open the safe using the emergency key.
For this, access the emergency lock. Introduce the key
provided with these instructions and turn it. The safe
will open.
Note: In case of an emergency opening due to a wrong
code, the emergency key opens the door but does not
unblock the electronic system.
6. OPENING WITH AN EXTERNAL
BATTERY
If the batteries have run out, you can use the safe by
placing a 9V battery in the power supply located to the
right of the keypad.
Once the safe is open, replace the batteries.
7. OTHER CONTROL ELEMENTS
SCREEN CONTROL: To configure the screen so it does
not display the digits that are entered, press the
button and then the 3 button (the screen will display
DP). If you would like the screen to display what you
enter, press the 3 button again (the screen will
display DP CODE).
SOUND CONTROL: To use the safe in silent mode,
press the button and then the 6 button (the screen
will display SILENT). If you would like the safe to emit
sounds again, press the
will display BUZZER).
BATTERY STATUS CONTROL: If you would like to know
whether the batteries are sufficiently charged, press
the button while the safe is closed. If the batteries
are fine, the screen will display HI-BAT, and if they
are not, the message will be LO-BAT. In that case, you
should replace the batteries with new ones.
In any case, if the batteries are not sufficiently charged,
the system will warn you of this when the safe is
opened and closed by displaying the OPEN LO-BAT or
CLOSE LO-BAT messages on the screen, respectively.
NOTE: During the battery change process, the safe will
not forget the codes that have been entered.
button. The screen will
6 button again (the screen