Battery Installation - Arregui BASA Manual De Instrucciones

IMPORTANT:
The first opening of the
safe you must use the
emergency key:
• Access the emergency
lock.
• Introduce the
emergency key and turn
it clockwise.
• Place the batteries
inside the battery holder
through the internal side
of the door.
• Close the safe with the key, on the closed lock position.
• Open the safe, insert the code 000000 and press the
button .
• Modify the codes as indicated in the point 2.
NOTE: Do not store the emergency key inside the safe

1. BATTERY INSTALLATION

Open the plastic cover located inside the door and place 4 1.5
V AA batteries.
2. PROGRAMMING THE OPENING CODES
This safe allows to program two secret opening codes--one
standard and one master, from 3 to 6 digits each.
The initial standard code is 000000 and the initial master code
is 888888. For your security, it´s important that you change
them and configure the codes you desire.
During the process, use the
entered.
Programming the standard code (the safe must be open):
A. Press 00 and the
SELECT.
B. Press the 0 button. The screen will display SET.
C. Enter your code (3 to 6 digits) and press the
The screen will display DONE.
With the door open, verify that the new code operates correctly
(see section 3, opening the safe).
Programming the master code (the safe may be open or
closed):
A. Press 00 and the
SELECT.
B. Press the 1 button. The screen will display OLD.
C. Enter the current master code (888888 the first time)
and press the
(if the code entered is incorrect, it will display ERROR).
D. Enter the new master code (3 to 6 digits) and press the
button. The screen will display REPEAT.
E. Enter the new master code again and press the
button. The screen will display DONE (if the code entered
is not the same both times, the screen will display
ERROR).
EMERGENCY LOCK
- +
button to delete the last digit
button. The screen will display
button. The screen will display
button. The screen will display SET
3. OPENING THE SAFE
Enter either of the two active opening codes and press the
button. The screen will display OPEN while the locks move,
and OPENED when the door has opened, and inside LED lamp
will bright 25 seconds automatically.
If an incorrect code is entered, the screen will display ERROR1,
for a second incorrect attempt it will display ERROR2, and for
a third incorrect attempt it will display ERROR3 and the system
will remain blocked for 5 minutes, indicating by blinking HOLD
5... HOLD 4... etc. During this time, the keypad cannot be used.
4. CLOSING THE SAFE
With the safe open, press the button
CLOSE while the locks move, and CLOSED when the door has
closed.
NOTE: If the locks encounter an obstacle, they will move back
and leave the door open.
5. OPENING WITH THE EMERGENCY KEY
If you do not have the opening codes, or if the batteries have
run out and an external battery is not available, you can open
the safe using the emergency key.
For this, access the emergency lock. Introduce the key
provided with these instructions and turn it. The safe will
open.
Note: In case of an emergency opening due to a wrong code,
the emergency key opens the door but does not unblock the
electronic system.
6. OPENING WITH AN EXTERNAL BATTERY
If the batteries have run out, you can use the safe by placing
a 9V battery in the power supply located to the right of the
keypad.
Once the safe is open, replace the batteries.
7. OTROS ELEMENTOS DE CONTROL
SCREEN CONTROL: To configure the screen so it does not
display the digits that are entered, press the
button.
then the 3 button (the screen will display DP). If you would like
the screen to display what you enter, press the
again (the screen will display DP CODE).
SOUND CONTROL: To use the safe in silent mode, press
the button and then the 6 button (the screen will display
SILENT). If you would like the safe to emit sounds again, press
the 6 button again (the screen will display BUZZER).
BATTERY STATUS CONTROL: If you would like to know
whether the batteries are sufficiently charged, press the
button while the safe is closed. If the batteries are fine, the
screen will display HI-BAT, and if they are not, the message
will be LO-BAT. In that case, you should replace the batteries
with new ones.
In any case, if the batteries are not sufficiently charged, the
system will warn you of this when the safe is opened and
closed by displaying the OPEN LO-BAT or CLOSE LO-BAT
messages on the screen, respectively.
NOTE: During the battery change process, the safe will not
forget the codes that have been entered.
En
. The screen will display
button and
3 button