Programming The Machine; Drainage - Saeco Royal SUP 016 E Manual Del Usuario

87
Remove water tank (11) from the machine,
remove its cover (12) and fill it with cold water
(approx. 2.4l). A valve on the tank bottom
prevents water from escaping.
Before installing the water tank in the
machine, make sure the coffee bean
container cover is properly fitted.
31
Install the water tank, slightly pressing over it to
fit the valve which will open automatically.
Do not fill the tank with an excessive quantity of
water.
Always fill the tank with fresh water only: hot
water as well as other fluids might damage the
tank. Never use carbon dioxide added water.
Do not switch on the machine on if the water tank
is empty: always make sure there is enough
water in the tank!
Connect the plug to the socket and press the main
switch. The following message will be displayed:
"WARMING UP...... "
Should
"ENERGY
"SAVING
be displayed, press button "Standby" to
disactivate the energy saving mode.
DRAINAGE / PROGRAMMING THE MACHINE

Drainage

Direct the steam/hot water spout on the drip tray
(2). Place a cup or another suitable container
under the dispensing tube, then turn the steam/
hot water knob counterclockwise. The pump
starts automatically. Wait until a regular water jet
is obtained, then close the knob. The machine is
now drained and ready to work.
The following message will be displayed:
"SELECT PRODUCT
"READY FOR USE
Important: It is advisable to drain the
machine before the first start, after a
prolonged period the machine has not
been used or whenever the water
tank has been completely emptied.
Furthermore, should the pump be defective, the
display shows:
"VENTILATE

Programming the machine

32
To enter the programming mode, press the key
ENT ( pre-ground coffee) when the machine
is on and keep it pressed until the first two lines
of the programming mode are displayed:
"LANGUAGE
"RINSING
At the end of the line a blinking asterisk is
"
displayed, which can be moved up and down
"
with the keys (tall and regular coffee).
If the asterisk is on the first menu, press
to move it on the second menu and vice versa.
The display shows the following sequence of
88
messages :
LANGUAGE
RINSING
WATER HARDN.
CUP HEATER
TEMP. L. COFFEE
TEMP. COFFEE
TEMP. S. COFFEE
PREBREWING
PREGRINDING
"
" In order to exit from the program mode, press the
ESC key ( ). The machine is in normal mode
again
Selecting single menus
Select the different menu items by means of the
. The key ENT allows you to activate the
keys
selected item. It is possible to modify the selected
"
figures in a menu item using the keys
ENT memorizes the selected options (for instance
"ON" for the cup heating plate).
Should you accidentally change some data,
press ESC (
saving the new options which were selected
accidentally.
Language selection
Move the asterisk to the menu item
"
"LANGUAGE" using the keys
" ENT to activate this item. The following message
will be displayed:
button
The keys allow you to change the set options :
"DEUTSCH", "NEERLANDAIS", "ESPAÑOL",
"ENGLISH", "ITALIANO", "FRANÇAIS", or
"PORTUGUES".
Rinsing cycle function
If the rinsing cycle function is activated, the
PROGR. H. WATER machine that is started after a period of inactivity
starts a water rinsing cycle to the coffee dispensing
PROG. CAPPUC.
TOTAL COFFEE units automatically.
DESCALING Move the asterisk to the menu item RINSING
SIGN. DESCAL. CYCLE using the keys
TIMER
activate it.
VENDING
The display shows:
RINSING CYCLE
WATER CONNECT.
You can modify the chosen item with the key
Water hardness adjustment
In order to adjust the water hardness, it is necessary
to test the water using the strip supplied with the
machine. Dip the strip into the water for a second,
shake off excess water gently, wait approx. 1
. The key
minute and read the results.
Move the asterisk at the end of the line to the
menu item "WATER HARDN." using the keys
) to leave the menu item without
button.
The following message will be displayed:
. Press
The keys
options:
"LANGUAGE "
"ENGLISH "
Hardness 4
Hardness 3
Hardness 2
Hardness 1
PROGRAMMING THE MACHINE
and press ENT to
"RINSING "
"ON "
: on, off.
and select it by means of the ENT
"WATER HARDN. "
"HARDNESS 3 "
allow you to change the set
HARDNESS 4
(hard water)
HARDNESS 3
(medium water)
HARDNESS 2
(soft water)
HARDNESS 1
(very soft water)