Grind Adjustment; Brewing - Saeco Royal SUP 016 E Manual Del Usuario

95
"DREGDRAWER FULL
"READY FOR USE
The machine does not stop: remove the grounds
container and empty it.

Grind adjustment

If the coffee flows too quickly (coarse grind) or too
slowly (fine grind) into the cup, adjust coffee grinder.
The recommended grind level is position 5.
Should grinding be too coarse, adjust it on a
lower value (e.g. from 5 to 3). On the contrary,
should grinding be too fine, adjust it on a higher
value (e.g. from 5 to 7).
Adjust the grind level only when the coffee
grinder is running. Avoid any extreme adjustment
(for instance on position 1) whenever possible.
It is preferable to try another coffee blend, since
not all coffee blends are suitable.
Coffee blends
Make sure coffee is fresh. An espresso roast is
preferable.
In order to obtain a strong and aromatic espres-
so coffee, use special blends suitable for espres-
so coffee machines and special cups with thick
sides.
Keep coffee in a cool place, in an hermetically
sealed container.
Operation time
The machine may be kept on all day long.
However, in case of a prolonged period of
idleness, it is advisable to enable the energy
saving function by pressing the standby
switch. If the timer is properly programmed, this
operation is automatic: for this purpose, see
page 90.
In case of a prolonged period of idleness, it is

BREWING

advised to switch the main switch (4) off; once
"
" switched on again, the machine will be ready
to be used within two minutes.
Switching off the machine
Switch the machine off only after the coffee cycle
has been concluded.
BREWING
Cup level filling
This machine allows the precise dosage of the
coffee quantity, according to the cup dimension.
The desired quantity can be selected
through the selection keys . The relevant messages
will be displayed.
To set the quantity of coffee to be dispensed, it
is necessary to press the relevant selection key
till the desired quantity of coffee is obtained
(max. 250 ml approx.).
During this operation, the following message is
displayed:
"1 SMALL COFFEE
"PROGR. QUANTITY
The machine considers automatically the
necessary amounts to brew two cups of coffee.
Attention! If the pre-brewing function is enabled
during the cups dosage adjustment, keep the
selected key pressed even during the pump stop
until the desired amount is reached.
Double quantity of coffee or 2 cups of
coffee
By pressing one of the three selection keys twice,
before coffee dispensing begins, the machine
will brew a double portion of coffee.
Coffee grinding
34
This machine grinds a portion of fresh coffee for
96
each cup; for two cups, it grinds two portions of
coffee, one after the other, thus ensuring optimum
coffee quality.
Adjust the grinding degree according to the
instructions mentioned at page 94.
Adjust the grinding degree only when the coffee
grinder is running.
Coffee dispensing
Place one or two preheated cups on the cupholder
grill (3) under the dispenser (6). By pressing the
relevant selection key, the machine will
automatically dispense the selected coffee.
Dispensing may be interrupted by pressing one
of the coffee selection keys, if an excessive water
amount has been selected. Should you interrupt
the coffee flow after the first of two coffees, the
second is not dispensed.
"
Pre-ground coffee
"
Make sure to use pre-ground coffee only (medium
ground). Never use whole beans or soluble
coffee.
Right before brewing coffee, fill the container
with freshly ground coffee. For best results, make
sure coffee blend is fresh.
Remember that ground coffee ages soon, thus
losing its quality!
35
Important!
Use the measuring spoon supplied to fill the
container (14) with a single portion of ground
BREWING
coffee! Use a full measure only.
To dispense coffee, press pre-ground coffee button
and the desired selection key (large coffee,
coffee, small coffee) to obtain a cup of coffee.
Important! This function does not allow the
double coffee cycle.
Dispensing may be interrupted by pressing one
of the coffee selection keys, if an excessive water
amount has been selected.
Hot water dispensing
Hot water dispensing is accomplished through
an independent water circuit which ensures the
correct temperature and supplies tasteless hot
water to be used for tea, soup, etc.
Press the hot water key, the display will show:
"WATER DISPENSING "
During hot water dispensing, only the
programmed amount is dispensed if the
corresponding programming is enabled. On the
contrary, dispensing should be stopped by
pressing again the selection key when the desired
amount is reached.
To program the hot water amount, it is necessary
to keep the corresponding selection key pressed
till the desired amount is reached.
Attention: hot water can only be
programmed if the corresponding
programming function is enabled (see
page 87).
During the programming phase, the following
message will be displayed:
"HOT WATER
"PROGR. QUANTITY
"
"