Setting Up A New Model Model Type: Acro; Activating Flight Phases; Managing Model Memories Menu: Memo; Transmitting Fail-Safe Positions To The Receiver Menu: (Memo) Sendfs - Multiplex COCKPIT SX M-LINK Manual De Instrucciones

Supplement to the manual
Receiver output 5:
= Aileron:
= Elevator:
= Rudder:
= Throttle:
= Spoiler:
= Flap:
= Flight phase switch:
Note: the flight phase switch PH can be used to select
three positions of the servo.
A brief press ( ) confirms your selected assignment.
Turn the rotary control to the left ( ) to EXIT and
return to the MIXER menu with a brief press ( ).
15. Setting up a new model
Model type: ACRO

15.9. Activating flight phases

What is possible with flight phases?
New:
C SX M-LINK transmitters allow you to set the
OCKPIT
value for Expo (EXP) separately for each flight
phase. The value is set using the same method as for
Dual-Rate ( 15.8.1. and
18. Managing model memories
Menu: MEMO
New:
Two additional menus:
Transmitting FAIL-SAFE settings to the receiver
Menu: SENDFS
Activating / disabling Fast Response
(14 ms frame rate)
Menu: F-RESP
18.6. Transmitting FAIL-SAFE
positions to the receiver
Menu: (MEMO) SENDFS
All M-LINK receivers feature FAIL-SAFE.
If no valid signal is picked up, the servos, speed con-
troller etc. move to user-programmable positions after a
certain waiting time (HOLD period). The following
methods of determining these positions are available:
1. The SET button on the receiver
Use the transmitter to move all the servos to the
desired positions, then briefly press the SET button
on the receiver
( see receiver instructions).
SX M-LINK SENDFS menu
2. C
OCKPIT
How to access the SENDFS menu:
to MENU,
to MEMO,
to SENDFS:
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
AI->S5
EL->S5
EU->S5
TH->S5
SP->S5
F-->S5
PH->S5
15.8.2.).
( 18.6.)
( 18.7.)
(SETUP appears),
(GO TO appears),
Now briefly press the 3-D digi-adjuster ( ).
The number 0 on the screen flashes.
Use the transmitter to move all the receiver outputs
(servos, speed controller) to the desired positions, and
hold them there.
Now turn the 3-D digi-adjuster to the right
It makes no difference whether you turn it by one or
more clicks. The number in the bottom line now runs
through the range 0 to7, indicating the transmission of
the seven FAIL-SAFE positions to the receiver. When
the process is complete, the 0 appears again, this time
not flashing.
You can now quit the menu by turning the 3-D rotary
via EXIT, or with a long press ( )
control to the left
on the 3-D digi-adjuster.
18.7. Activating / disabling
Fast Response (fast frame rate)
Menu: (MEMO) F-RESP
The C SX M-LINK can generate servo signals
OCKPIT
with two different frame rates:
14 ms (Fast Response ON = 1), default setting
21 ms (Fast Response OFF = 0)
The servo signals are repeated every 14 / 21 ms.
! Note:
The faster frame rate (14 ms) may cause analogue ser-
vos to run jerkily or oscillate. At the 21 ms frame rate all
servos should work without problem. F-RESP can be
set separately for each model memory.
How to access the menu F-RESP:
to MENU,
to MEMO,
to F-RESP:
Press the 3-D digi-adjuster ( ) briefly.
The number (0 or1) on the screen flashes.
You can now use the 3-D digi-adjuster to select your
preferred servo frame rate:
1 = Fast Response ON = 14 ms
0 = Fast Response OFF = 21 ms
Press the 3-D digi-adjuster briefly ( ) in order to confirm
your choice.
The number on the screen ceases to flash.
You can quit the menu by turning the rotary control to
via EXIT, or with a long press ( ) on the
the left
3-D digi-adjuster.
.
(SETUP appears),
(GO TO appears),
Page 27