Protecting The Environment - Stanley FATMAX FME720 Manual Del Usuario

@
Warning! Do not use any blade that requires a
spacer or spindle ring to fit. Only use blades as
specified in this manual.
@
Changing blades (fig. O - Q)
Warning! To avoid injury from accidental
starting, always remove the power plug from
the power source before changing the blades.
Use correctly sharpened saw blades. Observe
the maximum speed and tooth type marked on
the saw blade. Only use STANLEY FATMAX
recommended blades.
To replace the saw blade (34), proceed as follows:
● Press the saw arm release lever (36) and rotate the
moveable lower guard counter clockwise and clear of the
blade. Use one hand to hold the guard in place (fig. O).
● Using a screwdriver, loosen but do not remove the
screw (50). Do not remove the screw completely as this
will make re-assembly difficult.
● Using a screwdriver, loosen but do not remove the
screw (51) until there is movement in the metal guard
plate. Do not remove the screw completely as this will
make re-assembly difficult.
● Move the metal upper guard plate counter clockwise
(fig. P). This will give you access to the spindle bolt (52)
that attaches the saw blade (34) to the mitre saw.
● Press and hold the spindle lock button (35) on the
motor housing, to lock the saw blade (34) and prevent it
from rotating.
● Using the supplied blade spanner, turn the spindle
bolt (52) in a clockwise direction to remove the bolt and
the saw blade (34).
● Fit a replacement blade, make sure that the teeth are
pointing downward and the direction marking on the blade
is the same as that on the mitre saws guard (clockwise)
(fig. P).
● Loosely fit the spindle bolt (52) by hand (turn
counter clockwise).
● Press and hold the spindle lock button (35) and use the
blade spanner to tighten the spindle bolt (52) until the
blade is secure.
● Replace the metal upper guard (26) into its original
position and tighten the two screws (50 and 51).
● Allow the moveable lower guard (5) to return to its original
@
position covering the blade.
Warning! Never press the spindle lock while
the blade is rotating. Be sure to hold the guard
bracket down and firmly tighten the guard bracket
screw after installing the blade.
(Original instructions)
@
Warning! The guard bracket must be returned
to its original position and the screw tightened
before activating the saw. Failure to do so may
allow the guard to contact the spinning saw
blade resulting in damage to the saw and severe
personal injury.
Accessories
The performance of your tool depends on the accessory used.
STANLEY FATMAX accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
Warning! Before performing any maintenance
on the tool, unplug the tool. Unplug the charger
before cleaning it.
● Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
● Safely dispose of the old plug.
● Connect the brown lead to the live terminal in the
new plug.
@
● Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the
earth terminal. Follow the fitting instructions
supplied with good quality plugs. Recommended
fuse: 13 A.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
ENGLISH
15