Technical Specifications; Preparing For Installation - Jacuzzi VIRTUS Ficha Técnica De Preinstalación

En
It is the installer/owner's responsibility to check and
ensure compliance with the specific local regulations prior
to installation. Jacuzzi Europe S.p.A. gives no guarantee in
this respect and declines all responsibility for the compli-
ance of the installation carried out.

Technical specifications

Virtus ( 1) has two hydromassage pumps and one filter
pump. There is a filter on the edge of the tub to filter the water.
(where indicated) The water can be heated (or cooled) using a
Jacuzzi® Eco-Heat (CoolPower) heat pump which must be con-
nected to the hot tub (see the relevant documentation).
MAXIMUM POWER ABSORPTION OF SYSTEM
Power supply
Total consumption
(x)
(with heater)
Volt Hertz Ampere
~ 23
220-240 ~ 50/60
(k)
(k): at 230 V - (j): absorbed power
(x): see the "Preparing the electrical connections" chapter
The electrical system that powers the hot tub must be sized for
maximum consumption (as shown in the relevant tables).
Where there is an insufficient energy supply (models with
heater), an electronic limiter can still be activated; this reduces
consumption to 3.6 kW (when using a hydromassage pump, the
electric heater switches off).
HEAT EXCHANGER
- MAX primary inlet temperature .................................................... 50 °C
- Connections ............................................................................................ 3/4"
- Primary circuit flow rate .............................................................. 38 l/min
- Primary pressure drop ............................................................0.271 m H
WEIGHT
Net
MAX
Average volume
weight
of use
water volume
kg litres litres
~ 410 ~ 1500 ~ 2040
Total consumption
(with heat exchanger)
kW
Ampere
~ 5.35 ~ 16 ~ 3.65
(j) (k)
Max.
Resting Load on rest-
surface ing surface
total weight
kg m 2 kg/m
~ 2450 ~ 5 ~ 490
User safety
If the system has been installed by qualified personnel in com-
pliance with the installation manual, there are no risks for the
user. Safety, however, is also related to correct use, as specified
in the manual; and the user must entrust tall the operations de-
scribed in the installation manual to a qualified professional.
Check that installers and those managing the system are qual-
ified, in compliance with the regulations in force in the country
where the product is installed.
This appliance uses and generates radio waves: if it is not installed
and used as directed, it may cause interference with the reception of
radio and television programmes.
However, in special cases this may happen even if the instructions
provided are followed.

Preparing for installation

Semi-embedded models (with removable panels) (
kW
Create a support base under the bottom of the tub (concrete,
steel H-beams).
(j)
The hot tub can be semi-embedded, so that only the base of the
hot tub is embedded and the lateral covering panels are free. In
this case, it is advisable to prepare removable duckboards (made
of marine plywood or similar) which, besides improving the look
of the installation, facilitate the removal of the panels. The meas-
urements for the recess on the floor are the same as the base of
the hot tub (
( 6) If you want to install the hot tub against multiple
walls, a suitable space must be ensured for removing the
panels and for any maintenance.
Embedded models
- ( 8) Create a support base under the bottom of the tub (con-
crete, steel H-beams), (det.1).
It is also necessary to ensure that the pipes under the tub are acces-
sible, for instance by creating a passage around the external perim-
eter of the tub. This passage must be wide enough (approx. 80 cm)
to house all the electrical and hydraulic connections and to allow for
O any maintenance operations (det.2); it can be shut off with remov-
2
able boards (part.3), resting on suitable supports (det.4).
Any stagnant water must also be drained (det.5) and there must
be suitable ventilation.
Models with Jacuzzi® Eco-Heat/CoolPower heat pump
- You must leave the sides where there are appliances to connect
to the heat pump free (
2
- The heat pump can be positioned anywhere as long as it is no
further than 10 m away from the hot tub.
The heat pump must be installed in such a way that it cannot
be accessed by anyone without using keys or tools, and it must
be protected from water and weathering (it must also be suit-
ably ventilated).
12
1, 2a-b-c).
3, part. D/D1).
7)