Technical Data; Noise And Vibration Information - MIRKA DEROS 550CV Instrucciones De Manejo

en

Technical data

MIRKA®DEROS
Power
Mains voltage
Speed
Orbit
Size of backing pad
Weight
Degree of protection

Noise and vibration information

Measured values are determined according to EN 60745 .
MIRKA®DEROS
Sound pressure level (L
Sound power level (L
Sound measurement uncertainty K
Vibration emission value a
Vibration emission uncertainty K * 1 .5 m/s
Specifications subject to change without prior notice .
* The values stated in the table are derived from laboratory testing in conformity with stated codes and standards and
are not sufficient for risk evaluation . Values measured in a particular work place may be higher than the declared
values . The actual exposure values and amount of risk or harm experienced by an individual are unique to each
situation and depend upon the surrounding environment, the way in which the individual works, the particular
material being worked, work station design and the user's exposure time and physical condition. KWH Mirka Ltd
accepts no responsibility for the consequences of using declared values instead of actual exposure values for any
individual risk assessment .
Further occupational health and safety information can be obtained from the following websites:
http://europe .osha .eu .int (Europe) or http://www .osha .gov (USA)
Proper use of tool
This sander is designed for sanding all types of materials, i .e . metals, wood, stone, plastics, etc . using abrasives
designed for this purpose . Do not use this sander for any other purpose than that specified without consulting the
manufacturer or the manufacturer's authorized supplier . Do not use backing pads that have a working speed less than
10,000 RPM free speed . Only use original MIRKA backing pads that are designed for optimal performance with the
brake seal . Never mount a backing pad without a spacer washer . Other backing pads may reduce performance and will
increase vibration . The cooling air vents on the housing must be kept clean and unblocked to ensure air circulation .
Any maintenance or repair work requiring the motor housing to be opened may only be carried out by an authorized
service centre .
Work stations
The tool is intended to be operated as a hand held tool . It is always recommended that the tool should be used when
standing on a solid floor. It can be used in any position but before any such use, the operator must be in a secure
position, have a firm grip and footing and be aware that the sander can develop a torque reaction . See the section
"Operating instructions" .
44
Mirka® DEROS • 125 mm (5 in.) & 150 mm (6 in.)
550CV
350 W
220–240 VAC
4,000–10,000 rpm
5 .0 mm
Ø 125 mm
1000 g
I
550CV
) 71 dB(A)
pA
)
82 dB(A)
WA
2 .0 dB
*
3 .2 m/s
2
h
2
625CV 650CV
350 W 350 W
220–240 VAC 220–240 VAC
4,000–10,000 rpm 4,000–10,000 rpm
2 .5 mm 5 .0 mm
Ø 150 mm Ø 150 mm
1010 g 1010 g
I I
625CV 650CV
72 dB(A) 71 dB(A)
83 dB(A) 82 dB(A)
2 .0 dB 2 .0 dB
2 .4 m/s 3 .4 m/s
2
1 .5 m/s 1 .5 m/s
2
5650CV
350 W
220–240 VAC
4,000–10,000 rpm
5 .0 mm
Ø 125 / 150 mm
1010 g
I
5650CV
71 dB(A)
82 dB(A)
2 .0 dB
3 .4 m/s
2 2
1 .5 m/s
2 2