SFA SANIPACK Manual De Instalación página 8

1
DESCRIPTION
SANIPACK ® /SANINSIDE
specially designed to ta e the aste from a all hung or
bac to all WC pan.
The SANIPACK ® /SANINSIDE
from a WC, ashbasin and sho er.
SANIPACK ® /SANINSIDE
used correctly, SANIPACK
tent and reliable service.
Please note the following warning signs:
Possible danger to personnel,
Warning of possible electrical hazard.
WARNING This is a general arning that failure to follo
instructions could result in poor functioning of the unit.
2
LIST OF ACCESSORIES INCLUDED-
see dra ings.
3
DIMENSIONS- see dra ings.
4
TECHNICAL DATA
A p l p c i t a o i n
T y p e
Maximum Vertical Pumping
V l o a t g e
F e r q u e n y c
Normal Po er Rating
Maximum current consumption
E e l c r t c i C a l s s
Degree of protection
N t e W e g i t h
WARNING: Only installations conforming to the above
specifications are acceptable.
5
PERFORMANCE CURVE- see dra ings.
6
VERTICAL/HORIZONTAL PUMPING
COMBINATIONS- see dra ings.
7
INSTALLATION
SANIPACK ® /SANINSIDE
and should be installed by a qualified person.
WARNING: The unit must be connected to WC pan ith a
horizontal otlet spigot
The crusher has fastenings preventing it turning or from
moving.
7a
EXAMPLE OF INSTALLATION
7a1 7a2
See dra ings
WARNING: Provide an access panel of the follo ing
dimensions to enable the unit to be removed for
possible service:
L= 500mm x = 20mm if the side inlets are not
utilised
L= 00mm x = 20mm if the side inlets are utilised
WARNING: A screwdriver or other tool should be
required to remove the access panel.
Please note:
The SANIFLO range of pumps / macerators are fitted ith
thermal cut out protection.
In the event of continuous ater flo into the unit over a
long period E. a tap left running the motor ill cut out to
prevent damage and then self reset hen it has cooled
do n (after 30 minutes).
® is a compact pump/macerator
® ill pump a ay the aste
® is for domestic use. Installed and
® /SANINSIDE ® ill give consis-
1 W C + W a s
+ Shower
P 3 0
5 m
2 2 0 2 - 0 V
5 0 z
00 W
1, A
I
IP
5 5 ,
® is designed to fit behind panelling,
7a3
.
7b
CONNECTION TO A WC
The flexible sleeve is designed to fit onto the 100mm WC
pan spigot.
rease the pan spigot ith silicon lubricant or liquid soap.
Align the flexible sleeve ith the pan spigot.
Pull the flexible sleeve over the pan spigot using the t o
ears projecting from the sleeve.
WARNING:
a drop of at least 3
The distance from the WC pan to the SANIPACK
DE ® should not exceed 300mm maximum.
7c
CONNECTION TO SIDE-INLETS
(SHOWER AND WASHBASIN)
• To make the connection to the side inlets, use connector
Secure it ith clips
• Cap off unused inlets with plugs
(pre-grease the joint before fiting).
WARNING:
When fitting a sho er, ensure that the underside of the
tray is at least 15cm above floor level.
h b a s n i
7d
CONNECTION OF A WASHBASIN
The ashbasin can be connected in t o ays.
To one of the side inlets (see
Or to the raised inlet that can be cut open on the cover.
To do so:
• Cut off the top of the raised inlet with a saw.
• Do not leave any sharp angles on the edge of the cut.
Remove any burrs.
• Use a sleeve
7e
CONNECTION OF THE DISCHARGE PIPE
• Use the elbow and the stepped sleeve
• Fit the sleeve on the elbow. Fix it in place with a clip
• Orient the assembly as required and insert it into the
blac rubber pipe
ith clip
B
• If necessary, cut the end of the sleeve off to adapt it to the
size of the discharge pipe and use clip
it in place.
• We would recommend that a drain-off point is
installed to allo the discharge pipe or to be
drained do n before any service or .
• If the discharge pipework runs to a level considerably
lo er than SANIPACK
syphoning effect can suc out the ater seal in the unit.
Fitting an air admittance valve (
point of the pipe run ill overcome this problem.
WARNING:
pipe or , or 2 x 5 bends in series.
7f
ELECTRICAL CONNECTION
The electrical installation should be carried by a
qualified person. All wiring must conform to
BS7671, 1992 requirements for electrical
installations.The unit requires a 220/240V single
phase AC 50 Hz supply (UK specification).
Do not connect the unit to a conventional plug and soc et.
The unit should be connected to a fully earthed electri-
cal supply (class 1). It must be wired into an unswitched
fused fixed wiring connector protected by a 5 amp fuse
and a residual current detector (30 mA). This connection
must be used exclusively for supplying the unit.
8
The toilet must be installed at a level providing
for the outlet pipe.
.
B
D
7c
)
to connect the vertical pipe on the cover.
A
• Insert the Ø 40 mm waste pipe from the
ashbasin into the sleeve (clips sup-
plied).
c . Fix the base of the elbo in place
.
® /SANINSIDE
A approved) at the high
Use smooth pulled bends for discharge
® /SANINSI-
.
A
.
F
.
B
or clip to hold
G H
® unit, the resultant