Set A Number To Be Barred; Switch Baby Call On/Off; Set The Baby Call Number; Register A Handset - Motorola D710 Serie Manual De Instrucciones

D711_IFU_EN_for_EU.book Page 17 Friday, August 24, 2007 3:58 PM

Set a number to be barred

m d
1. Press , scroll to ADVANCED SET and press
d m
2. Scroll to CALL BARRING. Press .
3. Enter the master PIN (default setting 0000) and press
d m
4. Scroll to NUMBER. Press .
u d
5. If necessary, scroll or to the next available slot.
m
6. Press and enter the number or prefix you want to bar. Press
to confirm.
>
7. Press to return to standby.
Baby call
When activated, this feature allows you to dial a number by pressing any key on your handset
>
(except ). This feature is very useful for access to emergency services.

Switch baby call on/off

m d
1. Press , scroll to ADVANCED SET and press
d m
2. Scroll to BABY CALL. Press .
3. Enter the master PIN (default setting 0000) and press
m u
4. MODE is displayed. Press then press or
>
5. Press to return to standby.
NOTE
If you switch Baby call on, BABY CALL ON will be displayed on your screen in standby mode.
To switch Baby call off again:
>
1. Press .
m
2. OFF? is displayed. Press to confirm.

Set the baby call number

m d
1. Press , scroll to ADVANCED SET and press
d m
2. Scroll to BABY CALL. Press .
3. Enter the master PIN (Default setting 0000) and press
d m
4. Scroll to NUMBER. Press .
m
5. Enter the number. Press to confirm
>
6. Press to return to standby.
Dial a baby number
1. When a baby call number has been stored and the baby call setting switched on, press any
>
key (apart from ), to dial a number.
NOTE
When baby call is switched on, you can still answer any incoming call as normal.
Registration
Up to 5 handsets can be registered to one base station. Additional handsets must be registered
to the base before you can use them.
• The instructions described below apply specifically to your D711 handset. If you wish to
register another manufacturer's handset, the instructions may vary. In this case, please refer to
the manufacturer of the additional handset.
Advanced settings
• The Master PIN is required before you can register or unregister handsets. The default PIN is
m
.

Register a handset

m
.
At the base:
1. Press and hold the
m
At the handset:
1. Press
2. Scroll
3. If necessary, scroll
m
.
m 4. When the display shows PIN----, enter the base PIN.
.
d m
to select ON or OFF. Press to confirm.
Select a base
You can register your D711 handset with up to 4 bases. Once registered, you can switch between
bases, for example, bases at home and at work.
1. Press
2. Scroll
3.
m 4. Enter the number of the base you want – 1,2,3 or 4 and press
.
m
.
Unregister a handset
1. Press
2. Scroll
3. Enter the 4 digit master PIN and press
4. Scroll
PIN
The 4-digit master PIN is used when registering or unregistering a handset and when changing
some settings on your D711. The default setting is 0000. You can change this PIN for more
security.
1. Press
2. Scroll
3. Enter the current 4 digit master PIN and press
4. Enter the new PIN and press
0000.
p
button on the base station for at least 3 seconds. The base station
emits a beep when it is ready to accept registration. You have 90 seconds in which to register
a handset.
m d m
and scroll to ADVANCED SET and press .
d m
to REGISTRATION and press .
u d
or to display REGIST. BASE and press
the registered base number is flashing. Enter the number of the base on which you wish to
register your handset.
1
If you have only 1 base station, press . If you have 2 base stations, press
- When the handset registers with the base, it is assigned a handset number.
m d m
and scroll to ADVANCED SET and press .
d m
to REGISTRATION and press .
m
SELECT BASE is displayed. Press .
- The available bases are displayed with the current base number flashing.
- When the base is found you hear a beep. If not found, the display shows UNREGISTERED.
m d m
and scroll to ADVANCED SET and press .
d m
to UNREGISTER and press .
m
.
- Display shows the registered handset numbers.
u d
or to select the handset you want to delete and press
- UNREGISTERED is displayed on the handset screen.
m d m
, scroll to ADVANCED SET and press .
d m
to PIN. Press .
m
. (Default setting 0000)
m
.
m
. BASE 1 2 3 4 is displayed and
1 2
or , etc.
m
.
m
.
17