Prior To Operation - Stanley FatMax FME700 Manual De Instrucciones

ENGLISH
Maximum cutting capacity
Note: Capacity shown on chart assumes no wheel wear and
optimum fence position.
Workpiece
shape
90 cutting A = 4-7/8" A = 4-1/2"
O
(125mm) (115mm)
angle
A= 4-1/2" A = 3-13/16"
45 Cutting
O
(115mm) (98mm)
Angle

Prior to operation:

Install the appropriate cutting disc. Do not use excessively
u
worn discs. The maximum rotation speed of the tool must
not exceed that of the cutting disc.
Make sure the disc rotates in the direction of the arrows
u
on the accessory and the tool.
Secure the workpiece.
u
Always set the spark deflector correctly.
u
Switching on and off (fig. 1)
The on/off trigger switch (N) is mounted in the operating
handle.
To run the tool, press the on/off trigger switch (N).
u
Keep the on/off switch depressed while performing the
u
operation.
To stop the tool, release the trigger switch (N).
u
Warning: Do not switch the tool on or off when under load.
Warning: To prevent unauthorized use of tool, install a
standard padlock (not included) into the padlock hole (O)
located in the trigger switch.
&
Warning! Do not cut magnesium.
Consult your dealer for further information on the
appropriate accessories.
Performing a cut (fig. 1)
Place the material to be cut against the fence (E) and
u
secure using the vise (F).
Switch on the tool and pull down the handle to cut the
u
workpiece. Allow the motor to reach full speed before
cutting.
Allow the disc to cut freely. Do not force.
u
After completing the cut, switch off the tool and return the
u
arm to its upper rest position.
8
(Original instructions)
4-1/2" x 5-1/8" A = 4-1/2" x 5-3/8"
(115mm x 130mm) (115mm x 137mm)
4" x 7-5/8"
(115mm x 130mm)
3" x 7-3/8"
(115mm x 130mm)
4-1/2" x 3-13/16" A = 3-13/16"
4-1/8" x 3-3/4" 3-3/4"
(105mm x 95mm) (95mm)
Transporting (fig. 1)
The tool is equipped with a lock chain (A) which locks the
tool in closed-down position for carrying.
Warning: Ensure that the tool is switched off and
disconnected from the mains supply before transporting.
Lower the guard (K) onto the cutting table base (D) and
u
secure the tool in this position by securing the chain on
the hook in the handle.
Transport the tool using the carrying handles.
u
To release the tool, depress the operating handle slightly
u
and pull off the lock chain (A).
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper appliance/tool care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless appliance/tool:
Switch off and remove the battery from the appliance.
u
Keep the ventilation slots clear and regularly clean the
u
housing with a soft cloth.
Do not use abrasive cleaners.
u
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Motor brush inspection and replacement (fig. 9)
Warning! Turn off and unplug the tool. Be sure the trigger
switch is in the OFF position.
Brushes should be regularly inspected for wear. To inspect
brushes, remove brush cap (W). Brushes (V) should slide
freely in brush box. If brushes are worn down to .3" (8mm) as
shown in Figure 9 they should be replaced.
To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed.
Replace the brush cap (do not overtighten).
Cleaning
Blowing dust and grit out of the main housing by means of an
air hose is recommended and may be done as often as dirt is
seen collecting in and around the air vents. Always wear
proper eye and respiratory protection.