dosatron PJDI095 Manual De Instrucciones

Part #: PJDI095
D07RE5 - 3 GPM
Injection Seal Kit
This kit contains:
(1) J029 Plunger seal
(1) PDI550 Injection
sleeve key
(1) J051 Check valve
seal
(1) MPDI122 Check valve
assembly
(1) JDI092 (1) JDI092 Injection
stem o-ring
(1) P169 Check valve
barb
(1) 8J026 Injection
sleeve
o-ring
Vea el reverso para
instrucciones en Español.
3.
Unscrew the check
valve barb (P169),
remove the check
valve seal (J051),
unscrew the locking
nut (P168), remove
the anti-lock ring
(P189), and remove
the check valve
assembly (MPDI122)
from the stem.
4. Unscrew and remove
the adjusting sleeve
(PDI549). With the
help of a small flat
head screwdriver
PDI550
remove the plastic
injection sleeve key
(PDI550) located
inside the lower part
of the injection sleeve
(PDI538). Remove the
injection stem (PDI539)
from the bottom of
the injection sleeve
(PDI538). Replace the
injection stem o-ring
(JDI092) and injection
sleeve o-ring (8J026).
Kit Contents:
P169: Check
valve barb
MPDI122: Check
valve assembly
J051:
Check
valve seal
We recommend cleaning all parts with
warm soapy water and a toothbrush
before installing the new parts. Water
normally lubricates the parts, but you may
use silicone on the o-ring to facilitate isertion.
Check valve may be taken apart and
cleaned in between maintenance to
remove particles.
CAUTION: Parts may contain
STOP
concentrated chemicals. The use of
Proper Protective Equipment is recom-
mended when performing maintenance.
Insert the injection
5.
stem (PDI539) into
the bottom part of
the injection sleeve
(PDI538). Make sure
P189
P168 that the long groove
in the injection stem
aligns with the hole in
MPDI122
the lower part of the
J051
injection sleeve. With
P169
the help of a small
flat head screwdriver
install the new
8J026
plastic injection
sleeve key (PDI550)
PDI538
all the way into the
injection sleeve
(PDI538). Thread
JDI092
the adjusting sleeve (PDI549) onto
the injection sleeve (PDI538) until it
reaches the top of the scale.
PDI539
To ensure hose is air-tight, you may choose to
carefully cut the top of hose before reinserting.
REMEMBER TO RESET YOUR INJECTION
RATE TO THE PROPER RATIO
PDI549
8J026: Injection
sleeve o-ring
PDI550: Injection
sleeve key
JDI092: Injection
J029:
stem o-ring
Plunger
seal
8J026
PDI538
PDI550
JDI092
PDI539
PDI549
Instructions
(Parts included in kit noted in blue)
1.
Unscrew
suction hose
nut (P153)
and remove
suction
hose.
2.
Unscrew and
remove injection
stem assembly
(CDDI066).
NOTE: If the
adjusting sleeve
(PDI549) starts
to unscrew,
tighten the lock-
ing nut (P168)
at the bottom
and the injection
stem assembly
will unscrew.
Using tools could damage the
plunger and affect the injection rate
6.
Reinstall the anti-
lock ring (P189)
and the locking nut
(P168). Insert new
check valve
assembly
(MPDI122) into
the injection stem
with the cone
pointing out.
Position the check
valve seal (J051)
onto the new
check valve barb
(P169) with the
groove facing up.
Thread the new
check valve barb.
7.
Replace the plunger
seal ( J029). Thread
the injection stem
assembly (CDDI066)
into the body. Slide
suction hose nut
(P153) onto the
CDDI066
suction hose,
PDI549
reattached suction
hose onto check valve
barb and tighten suc-
tion hose nut (P153).
P153
CDDI066
PDI549
P168
P189
P168
MPDI122
J051
P169
J029
P168
P153