Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Part PJDI154:
DM11RE3
- 11 GPM
Injection Seal Kit
This kit contains:
(1) J009
Plunger Seal
(1) PDI729
Check Valve
Cone
(1) JDI105
Check Valve
Cone O-Ring
(1) JDI105
Plunger
O-Ring
(1) PDI846
Isolation
Body
2090 Sunnydale Blvd.
Clearwater, FL 33765
800-523-8499 • 727-443-5404
www.dosatronusa.com
Kit Contents:
JDI105:
J009:
Check Valve
Plunger seal
O-Ring
PDI729:
PDI846:
Check Valve
Isolation Body
Cone
JDI105:
Check Valve
Cone O-Ring
CAUTION: Parts may contain
STOP
concentrated chemicals. The use
of Proper Protective Equipment is
recommended when performing
maintenance.
Instructions
(Parts included in the kit
noted in blue)
Unscrew hose
1.
PDI735
nut (PDI735)
and remove
the hose.
2.
Unscrew injection stem
assembly nut
(PDI702) and
PDI702
pull down on
PPDI045
the injection
stem (PPDI045) to
detach from the blue body,
and set aside.
3.
Remove the plunger (PDI848) by
giving it 1/4 turn counter clockwise
to unlock and
pull it down.
Remove,
discard the
old plunger
seal (J009)
and replace
with the new one.
4.
Remove the isolation body
(PDI846) by tilting and pulling out.
Replace with the new isolation
body firmly pushing it in place.
PDI846
5.
Unscrew the
check valve
nut (PDI734)
and pull out
the check
valve assembly
(PJDI115), from
the injection
stem assembly
(PPDI045).
6.
Remove the top guide (PDI739)
from the check valve assembly
(PJDI115), by giving it 1/4 turn
counter clockwise. Discard the
check valve cone (PDI729) and
check valve cone o-ring (JDI105).
Take the new check
valve cone (PDI729)
and install the new
check valve cone
o-ring (JDI105).
Insert the cone
part going down
into the check valve
barb (PDI740).
Place the check
valve spring (MDI358) on the rod of
the check valve cone (PDI729), then
attach the top guide (PDI739),
pushing it down and turning 1/4
clockwise until it locks.
7.
Insert the check
valve assembly
(PJDI115) back
into the bottom of
the injection stem
assembly
(PPDI045),
make sure the
tabs do not
overlap each other.
PDI848
Screw the check valve nut
JDI105
(PDI734) back on.
J009
8.
Insert the
injection stem
assembly
back into the
bottom of the
blue body and
screw on the
stem assembly
nut (PDI702).
9.
Cut 1" off from the top of the
suction hose to ensure a tight fit,
make sure
to cut in a
straight
PPDI045
line. Attach
the hose
and the
hose nut
PJDI115
(PDI735)
back onto
PDI734
the unit.
PDI739
MDI358
JDI105
PDI729
PDI740
PPDI045
PDI734
PPDI045
PDI702
PDI735

Publicidad

loading

Resumen de contenidos para dosatron PJDI154

  • Página 1 (PDI729) MDI358 noted in blue) and install the new Unscrew hose check valve cone JDI105 PDI735 nut (PDI735) Part PJDI154: o-ring (JDI105). PDI729 and remove Insert the cone DM11RE3 - 11 GPM the hose. part going down Injection Seal Kit...
  • Página 2 (PDI729) e instale MDI358 en el kit) el nuevo o-ring Desatornille (JDI105). Inserte JDI105 PDI735 la tuerca de Parte PJDI154: la punta del cono PDI729 la manguera en la lengüeta DM11RE3 - 11 GPM (PDI735) y remueva de la válvula la manguera.