Troubleshooting - Bissell POWERLIFTER REWIND 1413 Serie Manual Del Usuario

Maintenance & Care
Replace drive belt
Use only a genuine bissell style 9 replacement
belt (#203-1093) in your bissell vacuum.
1. Unplug cleaner from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (steps 1-4 of Check rotating
floor brush and drive belt), grasp old drive
belt and remove from motor pulley. Discard
old drive belt.
3. Place new drive belt over motor pulley and
stretch other end over rotating floor brush in
the space between the bristles.
4. Place ends of rotating floor brush down
into slots on sides as shown.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. if
properly installed, drive belt will center itself
on rotating brush.
6. Reposition the brush cover and screw
all six screws back into place.
clearing a clog
low suction or poor pickup may be due to
a clog in the vacuum cleaner. if you notice a
change in the sound of the motor or a reduction
in the spinning action of the dirt or brush roll,
check for clogs.
1. Unplug cleaner from electrical outlet.
2. Remove easy empty dirt tank from vacuum
base and empty dirt and debris.
3. Remove inner cyclone from easy empty dirt
tank (see page 10) and check for debris build-up
or clogs in the upper tank.
4. Check the suction inlet for a clog.
5. Grasp the hose wand to separate from the
hose wand base. Check for a clog in the base,
the wand or within the hose.
6. Remove the screw attaching the hose wand
base to the vacuum. straighten the hose wand
base and check for clogs with a long, narrow
object such as a broom stick. Do not use sharp
objects like a clothes hanger, as these may
puncture the hose.
7. if the clog persists, follow the instructions for
Checking the rotating floor brush on page 11 and
inspect the air passageway for obstructions.
www.bissell.com
12
All manuals and user guides at all-guides.com
WARnInG
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
4.
Motor
Pulley
WARnInG
To reduce the risk of injury from moving parts, turn
off vacuum cleaner and disconnect Power Plug from
electrical outlet.
3. 4.
5.
6.

Troubleshooting

problem possible causes
Vacuum Power cord not plugged in
cleaner won't
blown fuse/tripped breaker
turn on
incorrect height adjustment
Hose not attached to suction
opening
Crack or hole in hose
broken or worn drive belt
Rotating floor brush bristles worn
Vacuum
Rotating floor brush jammed
cleaner won't
pick up dirt
Clog in vacuum
Dirt tank full
Dirt tank or upper tank not
installed properly
Filters are dirty
Crack or hole in hose
Clog in vacuum
tool won't Dirt tank full
pick up
Dirt tank or upper tank not
installed properly
Filters are dirty
Vacuum cleaner
incorrect height adjustment
difficult to push
Dirt tank full
Visible dirt
escaping from
Filters missing or installed
cleaner
incorrectly
cord will
Knotted or twisted
not retract
Other maintenance or service not included in the manual should be
please do
performed by an authorized service representative.
not return
Thank you for selecting a bissell product.
this product
for any questions or concerns, bISSEll is happy to
to the store. be of service. contact us directly at 1-800-237-7691.
WARnInG
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
Remedies
Check electrical plug
Check/replace fuse or reset breaker
Adjust powerfoot to correct height setting
Grasp the hose wand and firmly push
into the hose wand base
Check hose and replace if needed
Replace drive belt, see page 11
Replace brush
Remove brush and clean debris from
brush ends, see page 11
Follow instructions on page 12 for
clearing clogs
empty dirt tank
Position correctly and lock in place
Check and clean or replace pre-motor
and post-motor filters, see pages 9-11
Check hose and replace if needed
Follow instructions on page 12 for
clearing clogs
empty dirt tank
Position correctly and lock in place
Check and clean or replace pre-motor
and post-motor filters see pages 9-11
Adjust powerfoot to correct
height setting
empty dirt tank
Check pre-motor and post-motor
filters for correct installation
Follow instructions on page 8
www.bissell.com
13