AmerTac Westek LW2002B Manual Del Propietário

LW2002B Owner's Manual
Location of Controls
1. Tap on / tap dim / tap off
2. Magnet*
3. Battery Compartment*
*On back of unit.
Installation with magnet or screws
Magnet (included) – Mount to any metal surface with magnet on back of unit.
Screws (included)
1. Remove the back of the unit so that is can be used as a template for the screw holes.
2. To do so, hold the light with the back of the unit facing up, sliding the back cover off.
3. Drill two (2) pilot holes in the location where you want to mount the light. Use the back of
the unit as a guide for the pilot holes.
4. Place screws (included) in pre-drilled holes. Do not over tighten.
5. Slide the light back on to the back of the unit.
6. To remove the light, simply slide the light off of the back cover.
ON/OFF/DIMMER Operation
1. Press once for full brightness.
2. Press again for softer light.
3. Press a third time to turn the light off.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove the back side of the Puck. To do so, hold the puck with the back side facing up.
Slide to the left and remove it.
2. Remove old batteries, if replacing batteries. Insert three new AAA batteries.
3. Make sure to follow battery polarity guide when installing new batteries.
4. Replace battery compartment housing.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended
use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.
One-Year Limited Warranty
AmerTac warrants to the original purchaser that this product will be free from defects in materials
and workmanship for a period of one year from the date of purchase. Additional details are
available at www.amertac.com. PROP. 65 WARNING: This product contains chemicals known to
the State of California to cause cancer and/or birth defects or other reproductive harm.
BATTERY OPERATED LED
RUGGED PUCK
Made in China / Fabriqué en Chine / Hecho en China
©2017 AmerTac™
250 Boulder Drive
Breinigsville, PA 18031
www.amertac.com
I17-0030-B