AmerTac Westek LW1205W Manual Del Propietário

LW1205W Owner's Manual
Location of Controls
1. ON/OFF Switch
2. Light Pivot
3. Battery Compartment*
*On back of unit.
Remote Control Buttons
4. Power on/power off
5. Adjust brightness + / -
6. Auto-off timer for 15, 30, 60 or 120 minutes
Installation
Note: Hook and loop tape may be cut to desired size for easier removal.
1. Check the location of where you want to place the under cabinet light. Make sure it is clean and there is no debris or dust. 1. Check the location of where you want to place the under cabinet light. Make sure it is clean and there is no debris or dust.
2. Two sets of hook and loop tape are included. Place the two pieces of hook and loop tape ogether so the hook and loop 2. Two sets of hook and loop tape are included. Place the two pieces of hook and loop tape ogether so the hook and loop
sides adhere to each other. Repeat this step for the second set of hook and oop tape.
3. Remove the plastic covering on one sticky side of the tape. Repeat this step for the second set of hook
and loop tape.
4. Place one set of the hook and loop tape in the left and right rectangular recessed areas on the base of
the under cabinet light.
5. Remove the plastic covering on the other sticky side of the tape. Repeat this step for the second set of
hook and loop tape.
6. Place the under cabinet light in the desired location. Press fi rmly for fi ve (5) seconds so the tape adheres to
the surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or
damage surface.
Screws and Bracket (included)
1. Remove both pieces of hook and loop tape by pulling the tape away from the base of the light.
2. Remove the mounting bracket so that it can be used as a template for the screw holes.
To do so, hold the light with mounting bracket facing up.
3. Drill two (2) pilot holes in the location where you want to mount the under cabinet light. Use the detachable bracket as a
guide for the pilot holes.
4. Place screws (included) in pre-drilled holes. Do not over tighten.
5. Clip the under cabinet light to the bracket by aligning and inserting the light in the bracket.
6. To remove the under cabinet light from the bracket, simply pull down.
Operating Directions
Light Positioning
Light head rotates by simply turning light to direct where you need it.
NOTE: To prevent damage to the unit, do NOT overturn the light head.
Doing so may damage the unit and will void the warranty.
Remote Operation
Remove plastic tab from remote prior to use.
Use the top left red button to power on and top right button to power off.
adjust brightness of light with the + / - buttons in the middle section of remote.
The auto-off timer feature may be set by pressing the corresponding 15, 30, 60 or 120 button on the remote control.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove the mounting bracket at the back side of the Under Cabinet Light. To do so, hold the light with mounting bracket
facing up and the power button facing you. Slide the mounting bracket to the left and pull up to remove it.
2. Pull up on the battery compartment housing tab to open the battery compartment.
3. Remove old batteries, if replacing batteries. Insert three new AA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
Replacing the batteries in the remote control –
If the remote control does not work to turn the LED light on, this may be an indication that the battery needs to be replaced.
Replacing the battery
1. Follow illustration on back of remote
2. Remove battery cover by pushing in small tab to left and sliding battery compartment out
3. Remove the old battery (if replacing)
4. Insert new CR2025 battery. Be sure to match the battery polarity guide when installing new battery.
5. Slide battery drawer in
This product contains a button battery. If swallowed, it could cause serve injury or death. Seek medical attention immediately.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited
express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The
Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions
explained fully in the Limited Warranty on the website.
REMOTE CONTROLLED BATTERY OPERATED
LED SWIVELING BAR LIGHT
Remote Control Back
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0049-A