SIZZIX Vintaj BIGkick Manual Del Usuario

The Sizzix® BIGkick™ Machine is exactly
what crafters have been looking for – a
versatile, easy-to-use and a ordable
multipurpose creative system. It is
designed to cut and emboss for creating
unlimited fun projects. Using the
DecoEtch and DecoEmboss
™
well as Sizzix Originals , Bigz
™
Clearlits and Embosslits™ Dies and
™
Simple Impressions ® Embossing Folders,
Textured Impressions ™ Embossing
Folders and Texturz Texture Plates,
™
crafters can now express their creativity
in minutes. Start unleashing the
limitless possibilities of your BigKick™
Machine to create a combination of
dazzling designs.
®
Using Vintaj Blanks in the BIGkick
®
DecoEmboss and DecoEtch dies are designed for use
with Vintaj blanks. Other manufacturers' metal blanks
may cause damage or premature wear to both the dies
and the machine.
Making Your Vintaj Brand Dies Last
To extend the life of your Vintaj brand dies, avoid repeatedly
placing the blanks in the same location on the die. Regularly
moving the blank to different locations on the die will ensure even
wear and minimize die distortion.
Use Only Vintaj Branded Dies When Forming Metal Blanks
The DecoPress Machine is compatible with most Sizzix
die-cutting products; however, Sizzix dies should not be
used to cut or shape metal unless they are Vintaj dies
specifically designed for that purpose.
IMPORTANT SAFETY INSTRUCTIONS
®
WARNING
precautions should always be followed, including the following:
a) Read all the instructions before using the appliance.
TM
b) To reduce the risk of injury, close supervision is necessary
when this machine is used near children.
c) Do not contact moving parts.
d) Only use attachments recommended or sold by the
manufacturer.
e) Do not use outdoors.
f) Always place and operate this machine on a clean, flat
surface.
g) PINCH HAZARD. AVOID ROLLERS.
h) DO NOT OVERLOAD THE MACHINE.
Dies, as
™ i) CUTTING HAZARD. AVOID CONTACT WITH THE DIE
BLADE.
, Sizzlits ,
™ ®
j) ADULT SUPERVISION OF CHILDREN RECOMMENDED.
SAVE THESE INSTRUCTIONS
Before attaching handle, remove protective cap on crank shaft and
discard. Then attach handle by sliding washer over hex screw and
inserting through handle and into crank shaft. Tighten hex screw
with hex wrench provided with handle kit. Press end plug over hex
screw until firmly sealed.
Machine
™
Vintaj Blank
DecoEtch Die
Solo Shim
Solo Platform
1. Place DecoEtch Die onto a Cutting Pad with foam side up.
Place Vintaj blank on the die. Place another Cutting Pad over
the blank to create a "sandwich." Place "sandwich" on Solo
Platform and Shim.
Slide "sandwich," Platform and Shim into the roller opening as
far as it will go. Note the rotation of the handle and continue to
rotate it in the same direction until the Platform and "sandwich"
have completely passed through the opening and the rollers.
– When using this product, basic
Assembly Instructions
Crank Shaft
Washer
Hex Screw
End Plug
Handle
Protective Cap
Using DecoEtch Dies
™
Cutting
Pads
Clips
"Sandwich"
Solo Platform & Shim
Using the Solo Platform and Shim
Improper use of the Solo Platform and Shim may cause
damage to the Machine. Read and follow the instructions
provided on the Solo Platform and Shim.
The Solo Platform and Shim are designed to be used together
when you are cutting or embossing thin materials such as
single sheets of paper, cardstock or Vintaj
when using heavy materials such cardboard, chipboard or
Grungeboard , or when embossing more than one layer of
®
cardstock, do not use the Solo Shim.
Solo Shim
Solo Platform
To attach the Solo Shim to the Solo Platform, insert the tab
of the Solo Shim into the Tab clips found on the end of the
Solo Platform.
Using DecoEmboss
™
DecoEmboss Folder
Cutting
Pads
DecoEmboss Folder
Solo Shim
Solo Platform
With the DecoEmboss Die open, insert a Vintaj blank, then close
like a book. Place Cutting Pad above and below the closed Folder
to create a "sandwich."
Solo Platform & Shim
Slide "sandwich," Platform and Shim into the roller opening as
far as it will go. Note the rotation of the handle and continue to
rotate it in the same direction until the Platform and "sandwich"
have completely passed through the opening and the rollers.
blanks; however,
®
Tab
Clips
Dies
"Sandwich"