Hoshizaki KM-100A Manual De Instrucciones página 5

ENGLISH
with the letter N or coloured Black. The wire which is coloured Brown
must be connected to the terminal which is marked with the letter L
or coloured Red.
* Should the socket outlets in the installation site not be suitable for the
plug supplied with your product, the plug must be removed (cut off if
it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord, it
must be disposed of. There should be no attempt to reuse it. Inserting
such a plug into a socket elsewhere presents a serious risk of electrical
shock.
* The non-rewirable plug must never be used without a fuse cover being
fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 10A and approved to BS 1362.
5. WATER SUPPLY AND DRAIN CONNECTIONS
WARNING
Connect to potable water supply only.
* The connections to the mains water supply must be made in
accordance with the countries' current requirements of the Water
Supply or Water Fittings Regulations.
* Icemaking water must be potable water. Where scaling can be
caused by water quality, installation of an external filter or softener
is recommended. Contact your local water treatment professional or
Hoshizaki service agent.
* Water supply pressure should be minimum 0.07 MPa (0.7 bar) and
maximum 0.8 MPa (8 bar). If the pressure exceeds 0.8 MPa (8 bar),
use a pressure reducing valve. Do NOT throttle back the supply tap.
* Be sure to use the new hose-sets supplied with the appliance. Do not
reuse any old hose-sets.
* A plumbing permit and services of a licensed plumber may be required
in some areas.
* Water should drain into an open trap.
* The icemaker drain is gravity flow, so ensure drain pipe has an
adequate pitch or fall.
* To prevent a backflow into the storage bin, the outlet hose must be
laid as shown in Fig. 2.
GOOD
Downgrade
Fig. 2
1) Attach the free end of inlet hose to the stop valve (Fig. 4), noting
washer is correctly positioned. Hand tighten sufficiently to provide
leak free joint. It is a wise precaution to have the stop valve within
easy reach.
2) Wrap P.T.F.E. tape around the hose adapter fitting, and screw the
hose adapter into the drain outlet of the icemaker. Hand tighten grey
flexible outlet hose (accessory) onto the hose adapter as indicated
All manuals and user guides at all-guides.com
II. OPERATING INSTRUCTIONS
BAD
Upgrade
BAD
1. OPERATION
The installer will normally commission the icemaker to start the automatic
icemaking process. To ensure continuous operation, make sure that:
* The water supply tap is on,
* The icemaker is plugged into the power supply, and
* The control switch is in the "ICE" position (remove the louver to check).
4
(Fig. 3). The pipe can be cut to length as necessary to suit position
of main drain. To prevent water leaks, secure the outlet hose to the
drain outlet by using a hose band.
Note: Jointing compounds should be approved and suitable for
potable water use.
Hose Adapter
Outlet Hose
Inlet Hose
Fig. 3
WARNING
1. This icemaker is designed to produce and store edible ice. To
keep the icemaker hygienic:
* Wash your hands before removing ice. Use the plastic scoop
provided (accessory).
* The storage bin is for ice use only. Do not store anything else
in the bin.
* Clean the storage bin before use (see "III. 1. CLEANING").
* Keep the scoop clean. Clean it by using a neutral cleaner
and rinse thoroughly.
* Close the door after removing ice to prevent entrance of dirt,
dust or insects into the storage bin.
2. All parts are factory-adjusted. Improper adjustments may result
in failure.
3. If the unit is turned off, wait for at least 3 minutes before
restarting the icemaker to prevent damage to the compressor.
Inlet Hose
Washer
Stop Valve
Fig. 4