Features And Controls; Operation; Spray Tips - Briggs & Stratton BPW1700 Manual De Instrucciones

Portable Residual Current Device Protection
This pressure washer is provided with a portable residual
current device (PRCD) built into the plug of the power supply
cord. This device provides additional protection from the risk
of electric shock. The PRCD provides 10 mA of protection.
Automatic Shut-Off
A sensor will detect an increase in pressure when releasing or
locking the spray gun trigger. The sensor will cause the motor
to shut off for as long as the spray gun trigger is released
or locked. If the motor continues to run when the spray gun
trigger is relased or locked, DO NOT USE THE MACHINE.
Contact a Briggs & Stratton authorized service dealer.
NOTICE Master switch should always be in the OFF
position (0) when pressure washer is not in use.
Motor Overload
An overload protection device automatically shuts off the
motor if it overheats or draws excessive current. If the
device trips, disconnect power by pressing master switch
to OFF (0) position. Let unit cool for 30 minutes and press
master switch to ON (I) position.
EU Disposal
This symbol indicates the owner of batteries and
electrical or electronic equipment shall not dispose
of this product with unsorted municipal waste. This
product should be disposed of in environmentally
appropriate waste locations. Please contact Briggs & Stratton
or your local retailer for additional disposal information.

Features and Controls

A Spray Gun
B Metal Nozzle Extension
C

Spray Tips (3)

D High Pressure Outlet
E Electric Cord w/ PRCD
F WaterTank
G Detergent Tank

Operation

Connecting Hose and Water Supply
3 4 5 6
NOTICE Use ONLY cold water (less than 38°C (100°F)).
1. Pressing red button (2,A) on gun, insert high pressure
hose (2,B) into gun until it snaps in place.
2. Attach high pressure hose (3,A) to outlet (3,B) and tighten.
NOTICE Make sure water source is capable of supplying water
at a flow rate greater than 11.4 LPM (3.0 GPM) and 0.14-0.55
MPa (1.4-5.5 BAR or 20-80 PSI) at end of garden hose.
3. Run water through garden hose to clean out debris.
NOTICE Using a backflow preventer at pump inlet could
cause pump damage. There MUST be at least 3 m. (10 ft.)
of unrestricted garden hose between pressure washer inlet
and backflow preventer.
WARNING! Water that has flowed through a
backflow preventer is considered to be non-potable.
4. Connect garden hose (4,A) (not to exceed 15 m (50 ft.))
to water inlet (4,B) and tighten.
Figure
1
H Water Supply Inlet
J High Pressure Hose
K Identification Label
L Master ON/OFF Switch
M Plastic Wand w/ Turbo Tip
N Steam Gun w/ Brush
Figure
5. Turn ON water, point gun in a safe direction, press trigger
lock button (2,C), then squeeze trigger to purge system of air.
6. Insert either wand (5,A) into spray gun (5,B), apply
inward pressure, and twist wand 1/4 turn clockwise
until securely in place.
NOTICE For metal nozzle extension, pull back on collar
of wand (6,A), insert desired spray tip (6,B), and release
collar. Tug on spray tip to secure in place.
Starting Pressure Washer
WARNING! Spray could splash back or propel objects
resulting in serious injury. Always wear indirect vented
(chemical splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
1. Press master switch (1,L) to OFF (0) (9,A) position.
WARNING! Risk of electrocution. Use of an extension
cord could cause electric shock or burn resulting in
death or serious injury. DO NOT use an extension cord
with this electric pressure washer. Your home's electrical circuit
receptacle or extension cord may not provide lifesaving portable
residual current device (PRCD) protection.
2. Plug electrical power cord (1,E) into a dedicated electrical
circuit (8) rated for 220 -240 volts AC at 10 Amps that is
properly insalled in accordance with all local codes and
ordinances. Circuit is not to supply any other electrical needs.
3. Press RESET button (7,C). Indicator light (7,B) should
be ON.
NOTICE Indicator light must be ON for the electric pressure
washer to operate.
4. Press TEST button (7,A). Indicator light (7,B) should be OFF.
5. Press RESET button (7,C). Indicator light (7,B) should
be ON.
WARNING! Risk of electrocution. Non-operating
PRCD could result in death or bodily injury. If
indicator light does not stay ON after test and
reset, do not use PRCD.
6. Press master switch to ON (I) (9,B) position.
7. Point gun in a safe direction, press trigger lock button
and squeeze trigger.
The motor will start and stop as spray gun trigger is depressed
2
and released.
Spray Tips
The turbo whirls a powerful pin-point jet of water for intense
cleaning. The black spray tip is for general soap applications.
The yellow spray tip is for general rinsing and high pressure
applications. The red spray tip is for maximum cleaning.
Usage Tips
• For most effective cleaning, keep spray tip from
20 to 61 cm. (8 to 24 in.) away from cleaning surface.
• If you get spray tip too close, especially using a high pressure
spray tip, you may damage surface being cleaned.
• DO NOT get closer than 15 cm. (6 in.) when cleaning tires.
Applying Detergent
WARNING! Chemicals could cause burns resulting
in death or serious injury. DO NOT use caustic liquid
with pressure washer. Use ONLY pressure washer
safe detergents/soaps. Follow manufacturers instructions.
Figure
1 7 8 9
Figure
1 10
5