Accessories - Femi 2201 SPECIAL Manual De Instrucciones

Check that the back of the blade goes to rest on the bearing
inside the upper part of the machine body A (Fig. 7): if it does
not, slacken the blade slightly and move it back into the right
position.
• fi t the protective casing.
• tightem the screw
At this point, activate button with small impulses so that the
blade positions itself correctly on the pulleys.
4.5 USING THE VICE (Fig. 10)
The chuck of the saw is of the quick sliding type so that the
slider easily and rapidly approaches the pieces to be locked.
To lock the piece to be cut in the chuck:
• place yourself in front of the machine;
• release the lever A towards the piece to be cut by unlocking
vice part B;
• position the slider at a few millimetres from the piece to be
cut;
• move the A towards the piece and lock it;
• turn lever C clockwise so as to defi nitely lock the piece
between the jaws.
If more pieces of the same bar are to be cut, you only need to
unlock and then re-lock the chuck by means of lever C.
If you need, instead, to change the bar, turn the lever C
counterclockwise to unlock the chuck and then pull lever A
towards you so that the slider moves away from the piece.
4.6 CORRECT POSITIONING OF THE PIECE IN THE
CLAMP (Fig. 10)
The pieces to be cut should be fi tted directly between the jaws
D without adding other objects.
WARNING: Never hold the pieces to be cut in your
hand.
When the pieces to be cut are profi led sections, fl at pieces or
special shapes, refer to the examples shown in the fi gures.
If the thickness of the profi led section is to be very thin, an
outline should be fi tted which copies the profi le inside the
profi led section itself to stop it being crushed between the
jaws.
4.7 CUTTING CAPACITY
The table below specifi es the cutting capacity at 90, 45 and 60
degrees which may be obtained in normal conditions of use
described in this manual and without placing any other object
between the jaws of the clamp.
12
All manuals and user guides at all-guides.com
Section
4.8
Section
5
5.1
Your sawing machine is equipped with a bi-metal blade
measuring 2140x19x0.9 mm.
For special requirements (see cutting table ), for example, for
cutting large solid sections or profi led sections or corner pieces
of small thickness, there are also blades avail-able with 4/6
toothing or 14 teeth per inch.
MATERIAL: .....................M42 (steel for springs + steel HSS)
EXTENSION: ............................................................mm 2140
HEIGHT: ........................................................................ mm 19
THICKNESS: ............................................................... mm 0,9
TOOTHING:.......................................................standard 6/10
Angle
90 gradi
45 gradi
60 gradi
CUTTING TABLE
S
Z/1" Mt/Min
Material
(mm)
Common
< 50 6/10
and special
> 50 4/6
steel
Aluminium
< 50 6/10
and alloy
> 50 4/6
Brass-
bronze
< 50 6/10
Stainless
> 50 4/6
steel
< 3 14
> 3<30 6/10
Iron tubing
>30 4/6
s
< 3 14
Profi les
> 3<30 6/10
>30 4/6

ACCESSORIES

CHOISE OF BLADE
.............................................. optional 4/6 - 14
Cutting capacity
(mm)
170
170 x 170
190 x 130
110
110 x 110
150 x 110
75
75 x 75
100 x 75
Nr
TF MF TF
60 4 2
30 3 1
60 6 2
60 6 2
30 1 1
30 1 1
60 6 2
60 4 2
30 3 1
60 6 2
60 4 2
30 3 1