Program Overview - tormatic T100 R Manual Del Usuario

6

Program overview

Menu 3 Basic settings
Menu Entry Selection
item
30 Door setting of upper end position
Reversal of the direction (press for 5 s)
31 Door setting of lower end position
32 Door setting for 1/2 opening position
33 Fine correction of upper end position
50 Factory settings
50 - 0 0...80 mm lower
50 - 99 0...80 mm higher
34 Fine correction of lower end position
50 Factory settings
50 - 0 0...80 mm lower
50 - 99 0...80 mm higher
35 Selection of closing edge safety device
Measurement display (press 5 seconds)
0 Optical closing edge safety device OSE
1 Electrical safety edge 8K2 (default setting)
2 Pressure wave switch with testing
3 Electrical safety edge 8K2 with slack rope
switch
4 Wireless closing edge, RadioBand
36 Selection of photoelectric sensor
0 Without photoelectric sensor (default setting)
1 2-wire photoelectric sensor LS2
2 4-wire photoelectric sensor LS5 photoelectric
reflection sensor
3 Photoelectric sensor LS2, mounted in frame
4 Photoelectric sensor LS5 photoelectric
reflection sensor mounted in frame
5 Light grid with testing (SG14)
37 Correction of pre-limit switch closing edge safety
25 Correction of pre-limit switch closing edge
safety (default setting)
25 - 0 0...50 mm lower
25 - 99 0...100 mm higher
38 Response of photoelectric sensor
0 No reduced open time (default setting)
1 Reduced open time with AR operation
- - Exit menu
Menu 4 Further door settings
Menu Entry Selection
item
40 Selection of operating mode
0 Dead man OPEN / dead man CLOSE
1 Pulse OPEN / dead man CLOSE
2 Pulse OPEN / pulse CLOSE (default setting)
3 AR - automatic closing
41 Response to closing edge safety device
0 Full reversing (default setting)
1 Partial reversing
Menu 4 Further door settings
Menu Entry Selection
item
44 Hold-open time in seconds
0 0 s (default setting)
1 - 30 1 s - 30 s (in increments of 1 s)
31 - 60 35 s - 180 s (in increments of 5 s)
61 - 99 190 s - 22.5 min (in increments of 30 s)
45 Status relay X5
0 Door close signal (default setting)
1 Door open signal
2 Status of door for traffic light control A800
3 2-minute garage light
4 5-minute garage light
5 On / off with hand-held transmitter (menu
item 62)
6 ELTACO wipe pulse
46 Status relay X6
0 Door close signal
1 Door open signal (default setting)
2 Status of door for traffic light control A800
3 Locking
4-14 Warning light closing (0 - 10 s warning time)
15-25 Warning light opening and closing (0 s - 10 s)
49 Motor duty cycle
0 Without limitation (default setting)
1 Geared motor 5.24 (25 min / 35 %)
2 Geared motor 5.24 WS (25 min / 30 %)
3 Geared motor 9.15, 9.20, 9.24 (25 min / 60 %)
4 Geared motor 9.24 WS (25 min / 20 %)
5 Geared motor 6.65 DU (10 min / 35 %)
6 Geared motor 14.15 (25 min / 60 %)
- - Exit menu
Menu 5 Various settings
Menu Entry Selection
item
50 Key switch function (J7)
0 Pulse input OPEN/CLOSE (default setting)
1 Inhibit control panel
2 Inhibit external control elements
3 Inhibit control panel and external control
elements
4 Activate control elements for 10 seconds
5 Switch-over to dead man mode for closing
6 Switch-over to 1/2 opening (winter mode)
7 Pulse input OPEN-STOP-CLOSE
8 Pulse input 1/2 OPEN-STOP-CLOSE
9 Automatic closing AR
10 Pulse input for smoke and heat extraction sys-
tem (setting in menu item 55)
11 Pulse input for smoke and heat extraction sys-
tem, inverted (setting in menu item 55)
12 Mutual locking of door
T100 R EN - 25