Troubleshooting - TFA 47.3006.01 Instrucciones De Uso

TFA_No. 47.3006_Anleitung 24.09.2021
Wireless rain gauge
• When it starts to rain the rain drop symbol begins to flash. If there is no precipitation for 30 minutes, the drops are no longer dis-
played.
• The rainfall amount is shown on a corresponding cylinder graph with 10 segments. The current scale (rainfall amount with filled
cylinder = 100 %) appears to the left of the graph. If the display range of the rainfall for the graph is exceeded, the scale changes in
25.4 mm (1 inch) steps. The cylinder diagram can represent a rainfall amount of up to 1270 mm (50 inches). If the rainfall exceeds
1270 mm, the cylinder will be displayed as completely filled.
9.3 Rainfall alert (24 hours)
• Press the RAIN/ALERT button in normal mode for 3 seconds to enter the rain alert mode.
• ALERT appears on the display and OFF flashes.
• To activate (ON) or deactivate (OFF) the function press the HIST/UP and DOWN button.
• The alert symbol and 2.0 mm (default) or the last adjusted alarm value appear on the display, if the rainfall alert is activated.
• Press the RAIN/ALERT button.
• The alarm value flashes.
• Press the HIST/UP or DOWN button to set the desired limit for the 24-hour rainfall alert while the indication flashes.
• Confirm the setting with the RAIN/ALERT button.
• If a selected alert limit is exceeded, an alarm sound will ring for 5 seconds at the base station. The alarm symbol flashes.
• The alarm tone will sound again for 5 seconds in every minute.
• Press any button to stop the alarm.
• The alarm symbol will continue flashing until the measured value is below the alarm limit.
9.4 Monthly rainfall history
• Press the HIST/UP button in normal mode to enter the history mode.
• HIST, the current year and month and the rainfall amount appear on the display.
• The instrument stores the values of 12 month. Press HIST/UP button again to scroll back the rain history for the last 11 months.
Hold HIST/UP and RAIN/ALERT button for 3 seconds in the history mode to clear the recorded reading.
• The device will automatically quit the history mode if no button is pressed for 5 seconds.
10. Illumination
• Press the SNOOZE/LIGHT button. The backlight turns on for 15 seconds.
11. Base station positioning
• The base station can be placed onto any flat surface with the stand at the back.
30
10:28 Uhr Seite 16
Wireless rain gauge
• Avoid being close to possible sources of interference that may affect radio reception. It is recommended to keep a distance of at
least 2 metres to possibly interfering sources (TV, computer, microwave, wireless phones, baby monitors) and large metal objects
(e.g. refrigerator). Within solid walls, especially ones with metal parts, the transmission range can be reduced considerably. In
extreme cases, please place the unit close to a window to improve reception.
• Do not use the base station in the vicinity of radiators, other sources of heat or in direct sunlight.
12. Mounting the rain and temperature transmitter
• Before the final installation, make sure that the measured values are transmitted from the transmitter at the desired installation site
to the base station.
• Also make sure that the transmitter is easily accessible for cleaning and maintenance. The transmitter should be cleaned from time
to time, since dirt and debris will affect the sensor's accuracy. The funnel should be routinely cleaned and freed from leaves and dirt.
• Place the transmitter horizontally in an area where rain can fall directly into the container, ideally 60 to 90 cm above the ground on a
small platform. If necessary, use the integrated water level.
• You can tighten the transmitter in the desired position with the two screws provided.
13. Battery replacement
• As soon as the corresponding battery symbol appears in the display, please change the batteries of the base station or transmitter.
• Please note: When the batteries are changed, the contact between the outdoor transmitter and the base station must be restored –
so always restart all devices or start a manual transmitter search (see "Outdoor values reception").

14. Troubleshooting

Problem Solution
➜ Ensure the batteries' polarities are correct
No indication
➜ Change the batteries
on the base station
➜ No outdoor transmitter is installed
No reception
➜ Check the outdoor transmitter's batteries
of the outdoor transmitter
Display "- -" (only use batteries/rechargeable batteries with 1.5V voltage!)
➜ Start the manual transmitter search: Press the HIST/UP button for 3 seconds
➜ Restart the outdoor transmitter and the base station according to the manual
➜ Choose another place for the transmitter and/or the base station
➜ Reduce the distance between the transmitter and the base station
➜ Check if there is any source of interference
31