Accessories; Troubleshooting; Storage, Transport, Disposal And Recycling; Limited Warranty - Permobil ROHO AGILITY Minimum/Mid Contour Back Support Instrucciones De Uso

Accessories

Warning: DO NOT install accessories on an AGILITY while the individual is in the wheelchair.
AGILITY Lumbar Support Pad*
*Not included with all models.
Notes: The AGILITY Lumbar Support Pad provides added support to the lumbar region.
Package contents include hook and loop fastener strips. The hook side of the fastener strip is pre-attached to the back of the Lumbar Support Pad.
To Install:
1. Detach the cover flap from the back shell and unzip the cover. Place the lumbar support pad inside the
cover, at the curve of the spine, or where it is most comfortable.
Note: The Lumbar Support may be placed either in front of or in back of the foam pad. Placement behind the
foam pad is recommended for models with the air insert. Placement in front of the air insert may reduce the
performance of the air insert.
2. Remove the backing from the loop side of the fastener strip and secure the lumbar support pad in the
desired position.
Note: If the loop fastener strip is attached to the inside of the cover, the fastener strip may need to be
replaced after multiple cover washings.
3. Zip the cover closed and re-attach the cover flap on the back shell.
ROHO AGILITY Laterals
Note: Only ROHO AGILITY Laterals should be used with ROHO AGILITY Minimum Contour Back Support and ROHO AGILITY Mid Contour Back Support. Refer
to the product information provided with the product.

Troubleshooting

For additional assistance, contact the equipment provider, distributor, or Customer Support.
The air insert is not holding air.
Not able to inflate or deflate an air insert.
The air insert does not feel comfortable.
The air insert slides inside the cover.
A component is damaged.

Storage, Transport, Disposal and Recycling

Storage or Transport: Clean and disinfect the product. Open the inflation valve. Deflate the product. Place in a container that protects the product from moisture,
contaminants and damage. After storing or transporting, inspect the product to ensure it was not damaged (see "Troubleshooting"), and follow instructions to
prepare the product for use.
Disposal: The components of the products in this manual are associated with no known environmental hazards when properly used and when disposed of in
accordance with all local/regional regulations. At the end of its useful life, treat as healthcare waste and dispose of according to local healthcare-waste guidelines.
Incineration must be performed by a qualified, licensed waste management facility.
Recycling: Contact a local recycling agency to determine recycling options for the product.

Limited Warranty

Limited Warranty Term, from the date the product was originally purchased: Back Shell: 60 months; Cover, Foam Pad, Foam Insert, Lumbar Support Pad and Air
Insert: 18 months. See also the Limited Warranty supplement provided with the product, or contact Customer Support.
ROHO AGILITY Minimum/Mid Contour Back Support Operation Manual
Confirm that the inflation valve is completely closed. Inspect for inflation valve and hose damage. Look for holes
in the air insert. If very small holes or no holes are visible, follow the instructions in the Repair Kit provided with
the product. For damage to the inflation valve or for large holes or leaks in the air insert, see the Limited Warranty
supplement, or contact Customer Support.
Confirm that the inflation valve is open. Inspect the inflation valve and hose for damage.
Add or remove air to adjust to your comfort level. (See "Cover Components - Air Insert Adjustment"). Make sure
air cells face the front of the wheelchair. Make sure the cover is properly positioned (see "Cover Removal and
Installation" and "Cover Components Installation").
Make sure the air insert is properly positioned and the fabric back is secured to the fastener strip in the cutout
area of the foam pad (see "Cover Components Installation"). The perimeter of the air insert should be tucked in
between the foam layers around the edge of the cutout area.
Contact Customer Support for a replacement.
8
To Remove:
1. Detach the cover flap closest to the
zipper and unzip the cover.
2. Carefully detach the hook and loop
fastener strips from each other.