Setting The Cycle Time; Dip Switch Setting - Kerbl HAPPYCOW Duo Instrucciones De Uso

6.3.2 Setting the cycle time

The cycle time is set at the factory to 60 seconds. If necessary, this can be
adjusted using the dip switch element on the circuit board (Fig. 8 - item 1)
to a value between 10 and 300 seconds. The cycle time may only be reset
following consultation with Kerbl. The default setting and therefore the
ideal setting for the Cow Cleaning Machine Duo is T3.

6.3.3 Dip switch setting

Below is the default setting of the dip switch element on the PCB for this
unit.
Once the unit has been restarted (connected to the power supply), the dip
switch changes will take effect and the settings will be briefly shown on
the display.
1 - 5
Machine type
2 3 1 4 2 5 3 6 4 7 5 8 6
F F 1 1 F F 1 1
F F 2 2 F F 2 2
F F 3 3 F F 3 3
F F 4 4 F F 4 4
F F 5 5 F F 5 5
F F 6 6 F F 6 6
F F 7 7 F F 7 7
F F 8 8 F F 8 8
6 - 9 10 - 12
Switch-off Cycle time
resistance
9 7 10 11 12 8 9 10 11 12
T T 1 1 – – 1 1 0 0 s s e e c c T T 1 1 – – 1 1 0 0 s s e e c c
T T 2 2 – – 2 2 0 0 s s e e c c T T 2 2 – – 2 2 0 0 s s e e c c
T T 3 3 – – 6 6 0 0 s s e e c c T T 3 3 – – 6 6 0 0 s s e e c c
T T 4 4 – – 9 9 0 0 s s e e c c T T 4 4 – – 9 9 0 0 s s e e c c
T T 5 5 – – 1 1 2 2 0 0 s s e e c c T T 5 5 – – 1 1 2 2 0 0 s s e e c c
T T 6 6 – – 1 1 8 8 0 0 s s e e c c T T 6 6 – – 1 1 8 8 0 0 s s e e c c
T T 7 7 – – 2 2 4 4 0 0 s s e e c c T T 7 7 – – 2 2 4 4 0 0 s s e e c c
T T 8 8 – – 3 3 0 0 0 0 s s e e c c T T 8 8 – – 3 3 0 0 0 0 s s e e c c
1 - 5 6 - 9
Machine type Switch-off
resistance
1 2 3 1 4 2 5 3 6 4 7 5
F F 9 9
F F 1 1 0 0
F F 1 1 1 1
F F 1 1 2 2
F F 1 1 3 3
F F 1 1 4 4
F F 1 1 5 5
47
10 - 12
Cycle time
Table:
Dip switch element
setting on the PCB
8 6 9 7 10 11 12 8 9 10 11 12
F F 9 9
F F 1 1 0 0
F F 1 1 1 1
F F 1 1 2 2
F F 1 1 3 3
F F 1 1 4 4
F F 1 1 5 5