Cleaning And Maintenance - Chicco TOGETHER Manual Del Usuario

Prolonged exposure to direct sunlight may
cause the fabric to fade.
• Prevent the stroller from coming into
contact with salt water. It may cause
rusting.
• Do not use the stroller on the beach.
• When it is not being used, the stroller
should be kept out of children's reach.

CLEANING AND MAINTENANCE

The cleaning and maintenance of this product must be carried
out on a regular basis by the user. The cleaning and maintenance
of the stroller must only be carried out by an adult.
CLEANING
The cover cannot be removed. Clean all fabric parts with a
damp sponge and neutral detergent. Please refer to the care
labels for instructions on how to clean the fabric parts. Below
are the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Periodically wipe clean plastic parts with a soft damp cloth.
Always dry the metal parts to prevent the formation of rust if
the stroller has come into contact with water.
MAINTENANCE
Lubricate the moving parts only if necessary, with the light
application of a silicone based lubricant. Regularly check the
condition of the wheels and, keep them clean of dust and sand.
To avoid friction that may prevent the correct operation of the
stroller, ensure that all the movable plastic parts placed along
the metal frame are clean of dust, dirt or sand. Keep the stroller
in a dry place.
GENERAL INSTRUCTIONS
ASSEMBLING AND OPENING THE STROLLER
CARRY-ALL TRAY
1. The mechanism which opens and closes the stroller is fitted
inside the carry-all tray. The 2 tabs on the end of the carry-all
tray are used to fasten it to the stroller frame: slide the 2 tabs
along the slots inside the handlebar (diag. 1A) and push the
tray towards the handlebar until you hear it click into place
(diag. 1B).
Check that the closing mechanism wire does not interfere with
the carry-all tray fasteners.
HOW TO OPEN THE STROLLER
WARNING: before you start, check that your children are at a
safe distance.
Ensure that during these operations the moving parts of the
stroller do not come into contact with your child.
2. Once the carry-all tray has been fastened to the frame,
move the sliding button on the tray (diag. 2A) to the left whilst
pressing the centre button and raising the handle (diag. 2B);
now open the stroller by using your other hand to push the
front section of the frame downwards, until you hear it click
into place (diag. 2C).
Make sure the stroller is open properly before proceeding any
further.
3. The rear seat on the stroller is fitted with a footrest. Once
the stroller is open, lower the footrest (diag. 3).
4. To adjust the height of the handlebar, press the two side
buttons (diag. 4) at the same time and move the handlebar to
the required position.
BASKET
5. The stroller comes with a practical carry-all basket. To
assemble the basket, slide the U-shaped tube into the tube
ends on the back of the stroller, as seen in diag. 5A. The
U-shaped tube is fitted correctly when you see the 2 grey rods
on the bottom, protruding from the holes below the stroller
frame tubes and you hear them click into place.
To finish, fasten the fabric to the tube using the press studs
(diag. 5B). Never use the carry-all basket without the supports
inserted properly. Always remove all contents from the basket
before you close the stroller.
6. You can also open the zip (diag. 6) on the back of the basket
to access it more easily.
FITTING THE BACK WHEELS
7. Parts needed to fit the back wheels: see diag. 7.
8. Remove the caps from the ends of the rear axle, then slot
the rear axle onto the frame, until you hear it click into place
(diag. 8).
WARNING: always check the rear axle is fitted properly before
using the stroller.
9. To assemble the wheels on the rear axle A) follow the
instructions in the correct order (see diag. 9A):
- the wheel B)
- the washer C)
- the spring pin D)
- the cap E)
Make sure you insert the fastening spring pin as indicated in the
diagram: the flat side must be inserted in the whole on the axle,
whilst the closed end of the spring pin must be facing outwards
(diag. 9B). Repeat the operation to assemble the other wheel,
following the instructions in the same order.
FITTING THE FRONT WHEELS
10. Slot the front wheel block onto the stroller frame as seen in
diag. 10, until you hear it click into place. Repeat this procedure
for the other wheel block.
WARNING: before use, make sure the wheel locks are properly
secured, by pulling them firmly.
BUMPER BAR
11. To assemble the bumper bar, simply slot it into the two
holes on the ends of the front armrests, as seen in diag. 11.
12. To remove the bumper bar, press the two buttons found
under the armrests, and pull the bar towards you (diag. 12).
WARNING: Always fasten your child with the safety belts. The
bar IS NOT a device for containing your child.
WARNING: Never use the bumper bar to lift the stroller up
with the child sitting in it.
20
HO
Th
13
the
fas
14
the
the
15
fig
pla
be
US
Ea
co
wi
mo
the
16
16
he
as
co
17.
the
(di
18
can
66
lef
19
at
WA
gu
WA
cro
AD
20
ba
the
21
ba
on
Th
str
TH
AD
22
the
rai
pre
WA
the
RE
Th
yo
23
wh
24