Memory Deletion - Nice Neomat T Serie Instrucciones Y Advertencias Para La Instalación Y El Uso

Note: if the programming described in point 4 is not confirmed the modifications are abort-
ed and the previous programming is maintained.
If after having programmed this function you wish to eliminate it, the procedure in table A13
must be followed, omitting step 3 which would modify position "1".
When position "2" is programmed, the electronic control unit automatically calculates the
difference between positions "2" and "1", so that each time a lower command is given, the
awning lowers to the greater of the two positions and then retrieves the fabric until arriving
to the lesser of the two positions.
4.3.8 - Programming of the "FTC" function
After having programmed positions "0" and "1", position "S" can be programmed that acti-
vates the "FTC" function for the automation of awnings with an automatic hooking mecha-
nism. Until the mechanism is working correctly, position "1" must be programmed a few
centimetres after the hooking point so that hooking occurs when retracting from point "1",
and position "S" is programmed a few centimetres after the release point so that the
ascent from point "S" is performed freely.
Follow the procedure indicated in table "12" to program position "S":
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A12" - Programming the release position "S"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Press and hold buttons ■ ▼ for another 5 seconds until
5s...
2 rapid beeps are heard. At this point the awning auto-
matically moves to position "1".
03. Use buttons ▼ and ▲ within 5 seconds to position the
1
awning in the release position "S" (below position "1").
S
04. Confirm the position by pressing buttons ▼ and ▲ of the
transmitter together within 5 seconds until 3 beeps are
heard. At this point the awning will automatically move to
position "0".
Note: if the programming described in point 4 is not confirmed the modifications are abort-
ed and the previous programming is maintained. If after having programmed this function
you wish to eliminate it, the procedure in table A13 must be followed, omitting step 3 which
would modify position "1".
All manuals and user guides at all-guides.com
4.3.9 - Modifying position "1"
Follow the procedure indicated in table "A13" to modify position "1":
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A13" - Modifying position "1"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Note: if the programming described in point 4 is not confirmed the modifications are abort-
ed and the previous programming is maintained.
By modifying position "1" the "FRT" and "FTC" functions are cancelled.

4.4 - Memory deletion

If you need to delete all the transmitter and the programmed operations, carry out the pro-
cedure shown in table A14.
The memory can be deleted:
• with a non-memorized transmitter starting from point A.
• with a previously memorized transmitter starting from point No. 1.
The following can be deleted:
• only the memorized transmitters, finishing at point No. 4
• all data (transmitters, sensor level, TTBUS address, etc.), completing the procedure
until point 6.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A14" - Memory deletion
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Press and hold buttons ■ ▼ for another 5 seconds until
5s...
2 rapid beeps are heard. At this point the awning auto-
matically moves to the position "1".
03. Use buttons ▼ and ▲ within 5 seconds to reposition the
awning in the new position to be programmed.
04. Confirm the position by pressing buttons ■ ▼ of the
transmitter together within 5 seconds until 3 beeps are
heard and a short up and down movement is performed.
A. Switch the motor off, activate the Step-by-Step input (by
P.P.
connecting the White cable with the White/Black one)
and keep it active until the end of the procedure.
B. Power the motor and wait for the initial beeps.
01. Press and hold down button ■ on a transmitter (about 5
5s...
seconds) until you hear a beep; then release it.
English – 7