Wall-Mounted Installation - Bpt Futura X2 Manual Del Usuario

English
General Notes
• Read the instructions carefully before beginning the installation and
carry out the actions as specified by the maker;
• The installation, programming, commissioning and maintenance of
the product must be carried out only by qualified technical personnel,
correctly trained with regard to respecting the regulations in force,
including the implementation of accident prevention measures and
the disposal of packaging;
• Before carrying out any cleaning or maintenance operation, disconnect
the device from the power supply;
• The equipment must be destined solely for the use for which it was
expressly designed;
• The manufacturer declines all liability for any damage as a result of
improper, incorrect or unreasonable use.
• Warning: the unit contains a CR2032 lithium battery, danger of
explosion if the battery is replaced with one of the wrong type.
• Once batteries have run out, do not throw them away with unsorted
rubbish but collect them separately and send them for recycling.

Wall-mounted installation

Unfasten the equipment from the metal support by letting it run
smoothly along it after you have pressed the plastic button A.
Fix the metal support to the round Ø 60 mm back-box B or the
rectangular 503 back-box CD using the screws provided and paying
attention to the UP direction indication (TOP) .
The box must be installed at an appropriate height for the user. Avoid
tightening the screws too much.
Once the connections are made, hook the video terminal onto the
metal support EF.
To unfasten the equipment from the metal support press the plastic
button and lift the terminal G.
For recessed installation refer to the recessing kit manual.
Technical features
Type
Local power supply (VDC)
Consumption (max mA)
Consumption with HEVC/MI (max mA)
Consumption in stand-by mode (mA)
Single LED consumption (mA)
(panic, disable ring tone)
Storage temperature (°C)
Operating temperature (°C)
IP Rating
Video standard
LCD TFT colour display (inches)
Terminal board H①
+
Local power supply
–
BUS line input
B
All manuals and user guides at all-guides.com
Futura X2
16÷18
300
410
<10
1
-25 ÷ +70
0 ÷ +35
20
PAL/NTSC
7
+
Doorbell
–
Alarm Input
AL
Audio entry panel
A
Output –
–
Video entry panel
V
+ Output +
Set-up of jumpers and trimmer function
Selection of last receiver on the line I (SW4)
HEVC/MI entry panel present J
Installation diagrams, limits and distances LM
If a UTP cat5 cable is used each pair of cables must power a single
receiver L
Ring tone settings
NOTE. See the entry panel documentation for call programming.
Entering Programming.
Press button 5 times in 5 secs.
A short tone confirms the entry into the programming.
Programming the ring tone associated to a call from the entry
panel (1 acoustic signal).
To listen to the ring tones in sequence press key .
To select the ring tone and exit programming press key
To select the ring tone and continue programming press key
Programming the ring tone associated to a call from the front
door (2 acoustic signals).
To listen to the ring tones in sequence press key .
To select the ring tone and exit programming press key
To select the ring tone and continue programming press key
Programming the number of call rings (3 acoustic signals).
Press key the same number of times as the rings selected for the call
(from 1 to 6 rings). Three seconds after the last press of the key the call
selected for the chosen number of rings will be played back.
To select the ring tone and exit programming completely press key
DISPOSAL - Do not litter the environment with packing material: make
sure it is disposed of according to the regulations in force in the country
where the product is used. When the equipment reaches the end of its
life cycle, take measures to ensure it is not discarded in the environment.
The equipment must be disposed of in compliance with the regulations
in force, recycling its component parts wherever possible. Components
that qualify as recyclable waste feature the relevant symbol and the
material's abbreviation.
CE Declaration - BPT S.p.A. a Socio Unico declares that this device complies
with directive 2004/108/EC. Original upon request.
.
.
.
.
.
7