Electrical Connection; Gas Connection - Ariston FH G S Manual De Instrucciones

Electrical connection

Ovens equipped with a three-pole power supply cable are designed to operate
with alternating current at the voltage and frequency indicated on the data
plate located on the appliance (see below).
Fitting the power supply cable
N
L
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indicated on the data
plate (see table).
The appliance must be directly connected to the mains using an omnipolar
switch with a minimum contact opening of 3 mm installed between the
appliance and the mains. The switch must be suitable for the charge indicated
and must comply with current electrical regulations (the earthing wire must not
be interrupted by the switch). The supply cable must be positioned so that it
does not come into contact with temperatures higher than 50°C at any point
(the back panel of the oven, for example).
! The installer must ensure that the correct electrical connection has been
performed and that it is fully compliant with safety regulations.
Before connecting the appliance to the power supply, make sure that
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance, which is
indicated on the data plate.
• The voltage is in the range between the values indicated on the data plate.
• The socket is compatible with the plug of the appliance. If the socket is
incompatible with the plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable and the
electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The manufacturer declines any liability should these safety measures
not be observed.
All manuals and user guides at all-guides.com
1. Open the terminal board by
inserting a screwdriver into the side
tabs of the cover. Use the screwdriver
as a lever by pushing it down to open
the cover (see diagram).
2. Install the power supply cable by
loosening the cable clamp screw
and the three wire contact screws
L-N- .
C o n n e c t t h e w i r e s t o t h e
corresponding terminals: the Blue
wire to the terminal marked (N), the
Brown wire to the terminal marked
(L) and the Yellow/Green wire to the
terminal marked (see diagram).
3. Secure the cable by fastening the
clamp screw.
4. Close the cover of the terminal
board.

Gas connection

The appliance should be connected to the main gas supply or to a gas
cylinder in compliance with current National regulations. Before carrying
out the connection, make sure the cooker is compatible with the gas supply
you wish to use. If this is not the case, follow the instructions indicated in the
paragraph "Adapting to different types of gas."
When using liquid gas from a cylinder, install a pressure regulator that complies
with current National regulations.
! Check that the pressure of the gas supply is consistent with the values
indicated in Table 1 ("Burner and nozzle specifications"( since this will ensure
the safe operation and longevity of your appliance while maintaining efficient
energy consumption.
! Should you need to install a gas hob on top of a built-in gas oven, it is strictly
forbidden to connect the two or to use a single cut-off tap. The two appliances
should be connected separately, and each one should have its own stop tap in
order to make them completely independent from one another (see figures(.
NO
Connection with a rigid pipe (copper or steel)
! Connection to the gas system must be carried out in such a way as not to
place any strain of any kind on the appliance.
There is an adjustable L-shaped pipe fitting on the appliance supply ramp
and this is fitted with a seal in order to prevent leaks. The seal must always be
replaced after rotating the pipe fitting (the seal is provided with the appliance(.
The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
Connecting a flexible jointless stainless steel pipe to a threaded
attachment
The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.
These pipes must be installed so that they are never longer than 2000 mm
when fully extended. Once connection has been carried out, make sure that
the flexible metal pipe does not touch any moving parts and is not compressed.
! Only use pipes and seals that comply with current National regulations.
Checking the tightness of the connection
! When installation has been completed, check the pipe fittings for leaks using
a soapy solution. Never use a flame.
Adapting to different types of gas
In order to adapt the oven to a type of gas other than the type for which it was
manufactured (indicated on the label), follow these simple steps:
• Replacing the oven burner nozzle
1. Open the oven door fully.
OK
9
GB