Publicidad
Idiomas disponibles
Idiomas disponibles
TAD-T32JW (GB/ES/FR) 10.6.17 8:58 AM ページ 3
6. AIR DEFLECTION (Fig. E)
The vertical louver (A4) may be set on right and left manual-
ly in desired direction.
7. STOP OPERATION
Press the Power button (C1).
TIMER OPERATION
Press the TIMER button (C7) when the unit is on, comes to OFF
Timer.
Press the TIMER button (C7) when the unit is off, comes to ON
Timer.
Set the desired time by pressing UP button "▲" (C9) or DOWN
button "▼" (C4) and press the TIMER button again. The blue
LED will light in the Emergency ON/OFF switch.
To cancel OFF Timer or ON Timer, press the Power button
(C1).
Timer setting range is 1 ~ 12 hours. ""00""= No timer setting.
EMERGENCY ON/OFF SWITCH (LED SCREEN) (A5)
This switch is used when the unit needs temporary ON/OFF.
When pressing the Emergency ON/OFF switch (A5), the unit
starts operation. The operation mode and the fan speed mode
are set at Auto.
Press the Emergency ON/OFF switch (A5) again, the unit stops
operation.
LED SCREEN
LED screen indicates the operation mode, timer operation
mode and warning.
The following is the detail of indications.
NOTE: Yellow LED presents Red/Green lights up simultane-
ously.
Operation mode
Cooling mode ................ (Blue)
Heating mode ................ (Red)
Dehumidify mode .......... (Yellow)
Fan mode ....................... (Green)
NOTE: Under AUTO mode, the unit will change its operation
mode automatically.
OFF Timer Operation
Cooling mode ................ (Blue)
Heating mode ................ (Red)
Dehumidify mode .......... (Yellow)
Fan mode ....................... (Green)
Blue LED lights up.
NOTE: Under AUTO mode, the unit will change its operation
mode automatically.
ON Timer Operation
Blue LED flashes.
Water tank full
If the water tank is full, red LED indicator flashes. When water
tank is full, the unit stops operation. After removing the water
from the tank, press the Power button to operate the unit and
the unit will be in the mode before water tank was full.
Filter Cleaning Indicator
Blue LED flashes.
NOTE: When the filters have to be replaced, blue LED flash-
es in the Emergency ON/OFF switch. Display only
when in operation mode.
CAUTION : When the blue LED starts to flash on "Emergency
ON/OFF switch" in front of Cabinet, please check
and clean the Air filters in the Rear Panel.
then press "Emergency ON/OFF Switch" for 4
seconds to reset and flashing. If necessary, please
replace the air filters.
Default Indicator
When default indicator lights on, internal wiring failure.
1. Upper part – Blue
2. Lower part – Blue
If get above 2 failures, please contact your dealer.
4. DRAINING EXCESS WATER (Fig. F)
1. Drain excess water from the tank by placing a pan under the
drain water outlet. (F2)
2. Remove the drain plug, and let the water drain into the pan.
3. When the water stops draining out, replace the drain plug,
put the tube back in the clip pointing up.
4. Remove the pan of water.
5. Operate the unit in Fan mode to dry the interior of the unit.
5. CLEANING
CLEANING AIR INTAKE GRILLE (Fig. G)
1. Clean the air intake grille (B1) once every two weeks.
2. To remove the air intake grille (B1), pull the grille off.
3. Remove the dust with a vacuum cleaner.
WARNING : DO NOT touch the evaporator. It may cause in-
CLEANING SURFACE
Clean the outside of the unit with a soft damp cloth.
CAUTION : NEVER use gasoline, solvents, chemical products
6. LONG-TERM STORAGE
Blue LED
At the end of the season, or when you do not plan to use the
unit for an extended period of time, the following procedures
LED Screen
are recommended.
(Blue, Red,
1. Run the unit 5 or 6 hours with only the "FAN" mode opera-
Yellow, Green)
tion in order to dry the inside.
2. Drain the water from the tank.
3. Unplug the unit.
4. Clean the unit by wiping off any dirt or dust on the unit with
a soft damp cloth or a vacuum cleaner, and then wipe again
using a soft dry cloth.
5. Clean the air intake grille (B1) and replace it.
6. Store the unit. Exhaust dusts can be put in
the rear panel. The original shipping carton
is the best place to store the unit. If you do
not have the original packing materials,
cover the unit with a large plastic bag and
store in a cool dry place.
CAUTION : ALWAYS store the unit in the vertical position.
7. TRANSPORTATION
Preferably keep the unit in the vertical position during trans-
portation. If this is not possible then lay it on its rear side, when
at destination put the unit back in the vertical position and wait
at least ten (10) minutes before using it. Before
transporting/moving the unit make sure the drain tank is empty.
CAUTION : ALWAYS lift the unit with the help of another
And
3
jury or damage.
or polish as they could damage the surfaces.
DO NOT put heavy objects on top of the unit.
person.
ENGLISH
Publicidad
