Installing The Antenna - Blaupunkt Helsinki RTM 127 Instrucciones De Montaje

• Installing the antenna

A wide range of different antennas is available in the market.
Combination antennas, for example, are an
For more information please contact your Bosch dealer.
Radio antenna
In new vehicles with antenna prefitting, e.g. VW, Seat, Audi, the power
is supplied to the antenna via the antenna cable (see user manual of your
car). If you wish to replace the original equipment for a conventional car
radio, you need to purchase an antenna duplexer (P/N 7 691 290 202)
from your specialist dealer. Information on how to install and connect
your antenna is provided in the antenna installation instructions. Accor-
ding
to the antenna type you wish to install, it may be necessary to use the
antenna adapter with holder included in the delivery (see Fig. 3a).
Telephone antenna
The Telephone ariel (GSM) shold be installed to 1m- distance from radio
one. After you have installed the antenna, tighten the connection at your
car radio by hand und add another 1/4 rotation using pliers.
Note: Make sure the telephone wires are not routed close to the
loudspeaker wiring.
• Installing the car radio
Install your car radio into the car radio compartment of your car.Uncover
the radio compartment (remove the shelf or the dummy panel) or cut the
car radio slot to a size of 182 x 53 mm. For the most common cars with
deviating installation places Blaupunkt offers specific 50-mm car radio
installation kits. Therefore, please check the car radio installation place
in your car. If required, use one of our car-specific installation kits.
Car radio sleeve or remote control installed in your
car
If your vehicle is equipped with a specific car radio mounting sleeve (e.g.
Opel), it is necessary to remove the original sleeve. Steering wheel
remote controls installed in some vehicles can be adapted by means of
an interface. Contact your specialist dealer for more information.
Installing the mounting sleeve
The mounting sleeve included with this car radio is designed for instal-
lation in vehicles with standard DIN installation compartment measuring
182 x 53 mm, 165 mm installation depth and a dashboard thickness of
1 to 20 mm in the area of the tab fasteners (see Fig. 1).Insert the car radio
into the sleeve and check which tabs on the sleeve can be bent with the
help of a screwdriver (see Fig. 1 and 2).
Note: Bend as many taps as possible.
Installing the car radio
Insert all connectors into the chambers until the side catches engage.
Place the car radio in the front of the sleeve and push it in gently on both
ends of the sleeve until the left and right side springs snap into place (you
will hear an audible click), see Fig. 3.
Advantage! Do not push on the display, keys or switches!
Removing the car radio
Insert the handles into the holes in the panel on the left and right side of
the radio and push them in until you hear an audible click (the side springs
unlock). Gently pull the unit out using both handles (see Fig. 3).
Note: Handles which have snapped into place can only be removed
after you have pulled the radio out of the compartment.
Connecting diagrams
Vehicles without car radio prefitting (page 10) .......................... Fig. 4
Power supply to standard ISO connectors (page 5) ................. Fig. 5
Power supply to car-specific connectors (page 5) .................... Fig. 6
i
nteresting solution.
Mounting and connection hardware included in the delivery
Loudspeaker connection 4x 4Ω/35 watts (page 5) ................... Fig. 7
Equaliser or amplifier connection (page 5) ............................... Fig. 8
LF = left front, RF = right front
LR = left rear, RR = right rear
Handsfree microphone connection (page 6) ............................. Fig. 9
Handset connection (7 607 570 512) (page 6) ......................... Fig. 10
CD player connection (CDC A06/072) (page 6) ........................ Fig. 11
IR remote control connection (RCT 07) (page 7) ...................... Fig. 12
CD player connection (CDC-A05/071) (page 7) ....................... Fig. 13
CD player connection (CDC-F05) (page 7) ............................... Fig. 14
Fix the guide pin with or without spacer
on the stud at the car radio rear side.
8 601 310 742
8 601 910 002
1
2
2
Telephon antenna
- 9 -
182
165
53
1-20
Fig.2
1
Fig.3
Radio antenna
Fig.3a
8 622 401 055