Actuador oleodinamico para cancelas abatibles (24 páginas)
Resumen de contenidos para SEA HALF TANK 270
Página 1
® Sistemi Elettronici Italiano Italiano di Apertura Porte e Cancelli International registered trademark n. 804888 English English Français Français Español Español Deutsch Deutsch ELECTROHYDRAULIC HALF TANK ATTUATORE OLEODINAMICO PER CANCELLI A BATTENTE HYDRAULIC SWING GATE OPERATOR OPERATEUR HYDRAULIQUE POUR PORTES A BATTANTES ACTUADOR OLEODINAMICO PARA CANCELAS BATIENTES ÖLDRUCKANTRIEBE FÜR SCHWINGTORE MANUALE D`INSTALLAZIONE...
Página 2
AC (with lock in opening and closing) Hydraulic locking is guaranteed on gates with length up to 1.80 m with the ELECTROHYDRAULIC HALF TANK 270 operator while for lengths up to 2.20 m use the ELECTROHYDRAULIC HALF TANK 390. An electric lock should be used for leaves (in all versions) exceeding those lengths.
Página 3
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 67410873 REV 05 - 12/2012...
Página 4
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 MECHANICAL/ELECTRONIC STOPS ASSEMBLING SCHEME T h e 4 s c r e w s ( A ) a r e s e l fta p p i n g s c r e w s a n d produce the thread during screwing.
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 STANDARD INSTALLATION EXIT ENTRY ELECTROHYDRAULIC HALF TANK operator 2) Mechanical stop 3) User 24 electronic control unit 4) Flashing lamp 5) Photocell Dx 6) Differential switch 16A - 0,03A 7) Photocell Sx 8) Start - stop push button with key...
Página 6
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 INSIDE OPENING INSTALLATION Total stroke 270 mm - max. recommended stroke 250 mm Max. Outside Stroke Max. Stroke Opening (mm) (mm) (mm) for 90°(mm) (mm) Angle...
Página 7
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 INSTALLATION ON MASONRY PILLARS, MAKING A NICHE * 270 Version * 1250 155 Min. ** 390 Version **1500 60 Min. If you have to make a niche observe the dimensions shown in fig.7.
Página 8
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 OSCILLATING FORK INSTALLATION PRELIMINARY -Open the package carefully, paying attention to not lose the parts reported in fig.3 -Fix the oscillating fork as in fig.8. Attention: do not use the hammer to insert the short brass pivot;...
Página 9
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 POSITIONING OF THE FRONT FIXATION Once the operator has been mounted on the back fixation close the leaf and do as follows: 1) Release the operator (as in Fig.
Página 10
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 INSTALLATION OF THE MECHANICAL LIMIT SWITCH STOPS - Release the unit (as in Fig. 33) - Let the rod come out about 3/4 of its run - To adjust the stop in opening act on disc, and in closing on disc 2.
Página 11
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 INSTALLATION OF THE CHROMIUM-PLATED ROD PROTECTION Make sure to have inserted the antivibration plastic frame (A) before inserting the rod cover extrusion (Fig. 22).
Página 12
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 ALUMINIUM RELEASE WITH KEY MOUNTING (accessory on request) The release key is kept in the inside of the aluminium release cover (see fig. 28) Fig.
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 PERIODICAL MAINTENANCE 1) Check the robustness and the stability of the gate; particularly the leaning and/or rotation Annual points of the gate ( hinges). 2) Check the oil level in the hydraulic/in oil bath operators Annual 4 Years...
NOTE: THE MANUFACTURER CAN NOT BE DEEMED RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED BY IMPROPER USE OF THIS PRODUCT. SEA reserves the right to do changes or variations that may be necessary to its products with no obligation to notice.
Página 15
® HALF TANK ELECTROHYDRAULIC Sistemi Elettronici di Apertura Porte e Cancelli English English International registered trademark n. 804888 To the attention of users and technicians RELEASE SYSTEM To release operate as follows: -Insert the key and turn it about 180° anti-clockwise (Fig.33). To relock the operator do as follows: -Insert the key and turn it clockwise until it stops (Fig.33).
Página 16
SEA. 4) PAGAMENTI Le forme di pagamento ammesse sono quelle comunicate o accettate di volta in volta dalla SEA. Il tasso di interesse sul ritardo da pagamento è del 1,5% mensile e comunque non oltre il tasso massimo legalmente consentito.
Página 17
The recognized defects, whatever their nature, shall not produce any responsibility and/or damage claim on the part of the Buyer against SEA. The guarantee is in no case recognized if changes are made to the goods, or in the case of improper use, or in the case of tampering or improper assembly.
Página 18
14. Transit through the leaves is allowed only when the gate is fully open. 15. The User must not attempt to repair or to take direct action on the system and must solely contact qualified SEA personnel or SEA service centers. User can apply only the manual function of emergency.
Página 19
3. Este producto fue diseñado y construido exclusivamente para el uso especificado en esta documentación. Cualquier otro uso no expresamente indicado puede afectar la integridad del producto y ser una fuente de peligro. El uso inadecuado es también causa de anulación de la garantía. SEA S.p.A. se exime de toda responsabilidad causadas por uso inapropiado o diferente de aquel para el que el sistema automatizado fue producido.
Página 20
International registered trademark n. 804888 Dichiarazione di conformità Declaration of Conformity La SEA S.p.A. dichiara che, con l’installazione degli adeguati dispositivi di sicurezza e di filtraggio disturbi, i prodotti: SEA S.p.A. declares that by installing the appropriate safety equipment and noise filtering the...
Página 21
® Sistemi Elettronici di Apertura Porte e Cancelli International registered trademark n. 804888 Note - Notes - Note - Notas - Anmerkung...
Página 22
è stato testato singolarmente al fine di garantire i più alti livelli qualitativi e la vostra soddisfazione. Vi ringraziamo per aver scelto SEA. This item has been produced following strict production procedures and has been singularly tested for the highest quality levels and for your complete satisfaction.
Página 23
N.B: L’estensione della garanzia legale di 12 mesi a 24 mesi e 36 mesi è va- lida solo se il presente modulo viene rispedito per posta o fax a SEA S.p.A. entro 15gg dalla data di acquisto. Allegare relativa fattura d’acquisto.
Página 24
® Sistemi Elettronici di Apertura Porte e Cancelli International registered trademark n. 804888 SEA S.p.A. Zona industriale 64020 S.ATTO Teramo - (ITALY) Tel. +39 (0)861 588341 r.a. Fax +39 (0)861 588344 www.seateam.com seacom@seateam.com...