Inclined plane
In order to alter the angle of slope, you initially have to loosen the two longer feet
(7) that are connected the trampoline, from the slings of the jumping mat (5) and
screw them on to the screw connections of the frame. Now select 2 shorter feet (8)
from the included accessories and fasten these with the screw connections of the
frame (place them on the side oft he longer feet, cf. Figure 5). There are 2 supports
on the opposite side of the longer feet (7). You should place a rubber stopper with
a rounded end (10) on each of them. All legs in this variant should use the rounded
rubber stoppers (10) instead of the flat rubber feet (9), cf. Figure 5.
You should in conclusion check, whether your trampoline is standing firmly on the
ground. If this is not the case, the trampoline washers (15) are provided for the
adjustment of the heights. You should on a trial basis, place as many of the washers
(15) as necessary, under the long foot (7) that does not touch the ground until the
trampoline stands firmly on the ground. You should thereafter remove the rubber
stopper (10) of the foot (7) and in its place, accordingly insert the required number
of washers (15). (Fig. 6)
The legs and rubber feet/-stoppers that are not used, can each case be attached to
the frame and hence not easily go missing.
STEP 5
The safety cushion (6) must be firmly attached to the frame before the trampoline
can be used (cf. figure 7). The trampoline must be placed firmly on the ground.
DIsMANTLING/foLDING of THe TRAMPoLINe
STEP 6
Unscrew the feet from the screw connections of the frame. Use the elastic band to
fasten the feet that are connected to the frame, to the slings on the bottom side of
the jumping mat (5).
STEP 7
You should remove the safety cushion, prior to folding up the trampoline. Place the
trampoline with the top down on a hard-wearing floor. Position yourself on the
frame of the trampoline in such a way that your left foot is in the middle of frame
section 4 and right foot is in the middle of frame section 3. Loosen the safety bolts
(11) from the trampoline frame. Hold frame section 1 with your left hand and frame
section 2 with the right one, and now pull in the two frame sections towards your-
self (see figure 8).
STEP 8
Fold the trampoline in the middle (see figure 9).
STEP 9
Now fold the entire trampoline as shown in figure 10.
MAINTeNANCe AND sToRAGe
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Do not make any structural changes. For your own safety, please use
original spare parts only. These can be sourced from HUDORA. If parts become
damaged or if sharp edges or corners should develop, the product may not be used
any more. If in any doubt, please contact our service team (http://www.hudora.de/
service/). Store the product in a safe place where it is protected from the elements,
cannot be damaged, and cannot injure anyone.
Store the trampoline in a dark area and protect it from dust and sharp objects.
Clean the cloth material with a brush. All other parts may be cleaned with a damp
cloth. Use the protective covers to protect windings from corrosion whenever the
legs are not installed.
DIsPosAL ADVICe
At the end of the product's life, please dispose of it at an appropriate collection
point provided in your area. Local waste management companies will be able to
answer your questions on this.
seRVICe
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous in-
formation on the product, replacement parts, solutions to problems and lost as-
sembly manuals at http://www.hudora.de.
8/16